Bedienungsanleitung Onkyo TX-NR906 (Seite 142 von 150) (Englisch)

62439

142

Zoom out

Zoom in

Vorherige Seite

1/150

Nächste Seite

142

Troubleshooting

If you have any trouble using the AV receiver, look for a

solution in this section. If you can’t resolve the issue

yourself, contact your Onkyo dealer.

Can’t turn on the AV receiver

• Make sure that the power cord is properly plugged into

the wall outlet.

• Unplug the power cord from the wall outlet, wait 5

seconds or more, then plug it in again.

The AV receiver turns off as soon as it’s turned

• The amp protection circuit has been activated.

Remove the power cord from the wall outlet immedi-

ately. Disconnect all speaker cables and input sources,

and leave the AV receiver with its power cord discon-

nected for 1 hour. After that, reconnect the power cord

and set the volume to maximum. If the AV receiver

stays on, set the volume to minimum, disconnect the

power cord, and reconnect your speakers and input

sources. If the AV receiver turns off when you set the

volume to maximum, disconnect the power cord, and

contact your Onkyo dealer.

There’s no sound or it’s very quiet

• Make sure that the digital input source is selected

properly (page 59).

• Make sure that the correct audio input is selected

(page 120).

• Make sure that all audio connecting plugs are pushed

in all the way (page 33).

• Make sure that the polarity of the speaker cables is

correct, and that the bare wires are in contact with the

metal part of each speaker terminal (page 23).

• Make sure that the speaker cables are not shorting.

• Check the volume. It can be set to

−∞ dB, −81.5 dB

through +18.0 dB (page 70). The AV receiver is

designed for home theater enjoyment. It has a wide

volume range, allowing precise adjustment.

• If the MUTING indicator is flashing on the display,

press the remote controller’s [MUTING] button to

unmute the AV receiver (page 71).

• While a pair of headphones is connected to the

PHONES jack, no sound is output by the speakers

(page 72).

• Check the digital audio output setting on the con-

nected device. On some game consoles, such as those

that support DVD, the default setting is off.

• With some DVD-Video discs, you need to select an

audio output format from a menu.

• If your turntable uses an MC cartridge, you must use

an MC head amp or MC transformer (page 46).

• Check the speaker settings (pages 95–102).

• The input signal format is set to PCM or DTS. Set it to

“Auto” (page 120).

• If there’s no sound from a DVD player connected to an

HDMI IN, check the DVD player’s output settings,

and be sure to select a supported audio format.

• Make sure that none of the connecting cables are bent,

twisted, or damaged.

Only the front speakers produce sound

• When the Stereo listening mode is selected, only the

front speakers and subwoofer produce sound.

• In the Mono listening mode, only the front speakers

output sound if the “Output Speaker” setting is set to

“L/R” (page 106).

• Check the Speaker Configuration (page 95).

Only the center speaker produces sound

• If you use the Dolby Pro Logic IIx Movie, Dolby Pro

Logic IIx Music, or Dolby Pro Logic IIx Game listen-

ing mode with a mono source, such as an AM radio

station or mono TV program, the sound is concen-

trated in the center speaker.

• In the Mono listening mode, only the front speakers

output sound if the “Output Speaker” setting is set to

“C” (page 106).

• Check the Speaker Configuration (page 95).

The surround speakers produce no sound

• When the Stereo or Mono listening mode is selected,

the surround speakers produce no sound.

• Depending on the source and the current listening

mode, not much sound may be produced by the sur-

round speakers. Try another listening mode (page 81).

• Make sure the speakers are configured correctly

(page 95).

The center speaker produces no sound

• When the Stereo listening mode is selected, the center

speaker produces no sound.

• In the Mono listening mode, only the front speakers

output sound if the “Output Speaker” setting is set to

“L/R” (page 106).

• Make sure the speakers are configured correctly

(page 95).

Power

Audio

If you can’t resolve the issue yourself, try resetting

the AV receiver before contacting your Onkyo

dealer.

To reset the AV receiver to its factory defaults,

turn it on and, while holding down the [VCR/DVR]

button, press the [ON/STANDBY] button. “Clear”

will appear on the display and the AV receiver will

enter Standby mode.

Note that resetting the AV receiver will delete your

radio presets and custom settings.

VCR/DVR

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR906 Seite 142

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR906

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info