Bedienungsanleitung Onkyo TX-NR906 (Seite 144 von 150) (Englisch)

62439

144

Zoom out

Zoom in

Vorherige Seite

1/150

Nächste Seite

144

Troubleshooting—Continued

• If your TV is connected to the HDMI output, set the

“Monitor Out” setting to “HDMI Main” or “HDMI

Sub” (page 52), and select “- - -” in the “Video Input

Setup” on page 56 to watch composite video, S-Video,

and component video sources.

• If your TV is connected to the COMPONENT VIDEO

MONITOR OUT, set the “Monitor Out” setting to

“Analog” (page 52), and select “- - -” in the “Compo-

nent Video Setup” on page 58 to watch composite

video and S-Video sources.

• If the video source is connected to a component video

input, you must assign that input to an input selector

(page 58), and your TV must be connected to either

the HDMI OUT or COMPONENT VIDEO MONI-

TOR OUT (pages 36 and 42).

• If the video source is connected to an HDMI input,

you must assign that input to an input selector

(page 56), and your TV must be connected to the

HDMI OUT (page 42).

There’s no picture from a source connected to

an HDMI IN

• When the “Monitor Out” setting is set to “Analog”,

and the “Resolution” setting is set to anything other

than “Through” (see page 55), no video is output by

the HDMI OUT.

• If the message “Resolution Error” appears on the AV

receiver’s display, this indicates that your TV does not

support the current video resolution and you need to

select another resolution on your DVD player.

The onscreen menus don’t appear

• If your TV is connected to the analog outputs, set the

“Monitor Out” setting to “Analog” (page 52).

• On your TV, make sure that the video input to which

the AV receiver is connected is selected.

•

On non-North American models, specify the TV system

used in your area in the “TV Format Setup

(not North American models)” on page 62.

The immediate display does not appear

• The immediate display will not appear when the input

signal from the COMPONENT VIDEO IN is output to

a device connected to the COMPONENT VIDEO

MONITOR OUT.

• Depending on the input signal, the immediate display

may not appear when the input signal from the HDMI

IN is output to a device connected to the HDMI OUT.

Reception is noisy, FM stereo reception is

noisy, or the FM STEREO indicator doesn’t

appear

• Relocate your antenna.

•

Move the AV receiver away from your TV or computer.

• Listen to the station in mono (page 73).

• When listening to an AM station, operating the remote

controller may cause noise.

• Passing cars and airplanes can cause interference.

• Concrete walls weaken radio signals.

• If nothing improves the reception, install an outdoor

antenna.

The remote controller doesn’t work

• Make sure that the batteries are installed with the cor-

rect polarity (page 15).

• Make sure that the remote controller is not too far

away from the AV receiver, and that there’s no

obstruction between the remote controller and the AV

receiver’s remote control sensor (page 15).

• Make sure you’ve selected the correct remote control-

ler mode (page 16).

• Make sure you’ve entered the correct remote control

code (page 137).

• Install new batteries. Don’t mix different types of bat-

teries, or old and new batteries (page 15).

• Make sure that the AV receiver is not subjected to

direct sunshine or inverter-type fluorescent lights.

Relocate if necessary.

•

If the AV receiver is installed in a rack or cabinet with

colored-glass doors, the remote controller may not work

reliably when the doors are closed.

• When using the remote controller to control other

manufacturers’ AV components, some buttons may

not work as expected.

• Make sure to set the same ID on both the AV receiver

and remote controller (page 117).

Can’t control other components

• If it’s an Onkyo component, make sure that the u

cable and analog audio cable are connected properly.

Connecting only an u cable won’t work (page 50).

• Make sure you’ve selected the correct remote control-

ler mode (page 16).

• If you’ve connected an u-capable Onkyo MD

recorder, CD recorder, u Dock to the TAPE IN/OUT

jacks, or an u Dock to the AUX 1 jacks, for the

remote controller to work properly, you must set the

display to MD, CDR, or DOCK (page 63).

If you cannot operate it, you will need to enter the

appropriate remote control code (page 137).

• The entered remote control code may not be correct. If

more than one code is listed, try each one.

• If none of the codes work, use the Learning function

to learn the commands of the other component’s

remote controller (page 140).

• With some AV components, certain buttons may not

work as expected, and some may not work at all.

• To control an Onkyo component that’s connected via

u, point the remote controller at the AV receiver. Be

sure to enter the appropriate remote control code first

(page 138).

Tuner

Remote Controller

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR906 Seite 144

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR906

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info