Bedienungsanleitung Onkyo TX-NR906 (Seite 143 von 150) (Englisch)

62439

143

Zoom out

Zoom in

Vorherige Seite

1/150

Nächste Seite

143

Troubleshooting—Continued

The surround back speakers produce no sound

•

The surround back speakers are not used with all lis-

tening modes. Select another listening mode (page 81).

• Not much sound may be produced by the surround

back speakers with some sources.

•

Make sure the speakers are configured correctly (page 95).

• While Powered Zone 2 is being used, playback in the

main room is reduced to 5.1-channels and the sur-

round back speakers produce no sound (page 130).

The subwoofer produces no sound

• When you play source material that contains no infor-

mation in the LFE channel, the subwoofer produces

no sound.

•

Make sure the speakers are configured correctly (page 95).

The Zone 2/3 speakers produce no sound

• The Zone 2/3 speakers only output sources that are

connected to an analog input. Check to see if the

source component is connected to an analog input.

• Powered Zone 2 cannot be used if “Speaker Type:

Front(Speaker A)” is set to “Bi-Amp” or “BTL”, or

“Speaker Type: Front(Speaker B)” is set to “Normal”,

“Bi-Amp”, or “BTL” (page 61).

There’s no sound with a certain signal format

• Check the digital audio output setting on the source

component. On some game consoles, such as those

that can play DVDs, the default setting is off.

• With some DVD-Video discs, you need to select an

audio format from a menu or with the [AUDIO] button

on your DVD player’s remote controller.

• Depending on the input signal, some listening modes

cannot be selected (pages 82-86).

Can’t get 6.1- or 7.1-channel playback

• While Powered Zone 2 is being used, playback in the

main room is reduced to 5.1-channels and the sur-

round back speakers produce no sound (page 130).

Can’t select the Pure Audio listening mode

• The Pure Audio listening mode cannot be selected

while Zone 2 is on.

The volume cannot be set as required (The vol-

ume cannot be set to +18.0 dB)

• Check to see if a maximum volume has been set

(page 115).

• After the Automatic Speaker Setup function has been

run, or the volume level of each individual speaker has

been adjusted (pages 71 and 100), the maximum vol-

ume may be reduced.

Noise can be heard

• Using cable ties to bundle audio cables with power

cords, speaker cables, and so on can degrade audio

performance, so don’t use them.

• An audio cable may be picking up interference. Try

repositioning your cables.

The Late Night function doesn’t work

• Make sure the source material is Dolby Digital, Dolby

Digital Plus, and Dolby TrueHD (page 109).

The DVD analog multichannel input doesn’t

work

• Check the DVD multichannel input connections

(page 120).

• Make sure that the multichannel input is assigned to

the input selector (page 60).

• Make sure that the multichannel input is selected

(page 80).

• Make sure that the “Speaker Type” is not set to

“Bi-Amp”. The multichannel DVD input cannot be

used if “Speaker Type” is set to “Bi-Amp” (page 61).

• Check the audio output settings on your DVD player.

About DTS signals

•

When DTS program material ends and the DTS bit-

stream stops, the AV receiver remains in DTS listening

mode and the DTS indicator remains on. This is to pre-

vent noise when you use the pause, fast forward, or fast

reverse function on your player. If you switch your

player from DTS to PCM, because the AV receiver does

not switch formats immediately, you may not hear any

sound, in which case you should stop your player for

about three seconds, and then resume playback.

• With some CD players, you won’t be able to playback

DTS material properly even though your player is

connected to a digital input on the AV receiver. This is

usually because the DTS bitstream has been processed

(e.g., output level, sampling rate, or frequency

response changed) and the AV receiver doesn’t recog-

nize it as a genuine DTS signal. In such cases, you

may hear noise.

• When playing DTS program material, using the pause,

fast forward, or fast reverse function on your player

may produce a short audible noise. This is not a mal-

function.

The beginning of audio received by an HDMI IN

can’t be heard

• Since it takes longer to identify the format of an

HDMI signal than it does for other digital audio sig-

nals, sound may not be output immediately.

There’s no picture

• Make sure that all video connecting plugs are pushed

in all the way (page 33).

• Make sure that each video component is properly con-

nected (pages 36-49).

• On your TV, make sure that the video input to which

the AV receiver is connected is selected.

• While the Pure Audio listening mode is selected, the

video circuitry is turned off and only video signals

input through HDMI IN can be output.

Video

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR906 Seite 143

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR906

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info