Bedienungsanleitung Onkyo TX-NR929 (Seite 65 von 160) (Englisch)

517568

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

Advanced Operations

En-65

Operating

procedure

(➔ page 61)

■ Speaker Impedance

` 4ohms:

Select if the impedance of any speaker is

4 ohms or more but less than 6.

` 6ohms

Select if the impedances of all speakers are

between 6 and 16 ohms.

■ Speakers Type(Front)

` Normal

Select this if you’ve connected your front

speakers normally.

` Bi-Amp:

Select this if you’ve bi-amped your front

speakers.

` Digital Crossover:

Select this if you’re using speakers without

crossover network.

Tip

• If “Speakers Type(Front)” is set to “Digital Crossover”, a

confirmation screen appears. Select “Next (2-7. Digital

Processing Crossover Network)” to display the screen

for Digital Processing Crossover Network (➔ page 68).

Continue with the settings.

■ Powered Zone 2, Powered Zone 3

` No

` Yes:

Zone 2/3 speakers can be used (Powered

Zone 2/3 enabled).

■ 11ch Playback

` No

` Yes

For 11.1-channel playback, set this setting to “Yes”. If

you select front wide speakers setting in Speaker

Configuration is set to “None”, it will be automatically

switched to “80Hz (THX)”.

Note

• Powered Zone 3 is not available in the following cases:

– The “Speakers Type(Front)” setting is set to “Bi-Amp” or

“Digital Crossover”.

– The “Powered Zone 2” setting is set to “No”.

• When the “Powered Zone 3” setting is set to “Yes” while

Powered Zone 2 is enabled (➔ page 84), the surround

back speakers cannot be used.

• When the “Powered Zone 2” setting is set to “Yes”, the

front wide speakers cannot be used.

• When the “Powered Zone 3” setting is set to “Yes”, the

front high speakers cannot be used.

•“11ch Playback” is not available in the following cases:

– The “Speakers Type(Front)” setting is set to “Bi-Amp” or

“Digital Crossover”.

– The “Powered Zone 2” setting is set to “Yes”.

– The “Zone 2 Monitor Out” setting is set to “Use”.

• If the “11ch Playback” setting is set to “Yes”, the audio of

front wide channel is output from FRONT WIDE PRE OUT

only.

Speaker Configuration

With these settings, you can specify which speakers

are connected and a crossover frequency for each

speaker. Specify “Full Band” for speakers that can

output low frequency bass sounds adequately, for

example, speakers with a good sized woofer. For

smaller speakers, specify a crossover frequency.

Sounds below the crossover frequency will be output

by the subwoofer instead of the speaker. Refer to

your speaker’s manuals to determine the optimum

crossover frequencies. If you set up your speakers

using Audyssey MultEQ XT32 Room Correction and

Speaker Setup, please make sure manually that any

THX speakers are set to “80Hz(THX)” crossover.

■ Subwoofer

` Yes

` No

■ Front

` Full Band

` 40Hz to 80Hz(THX)

to 100Hz, 120Hz, 150Hz,

200Hz

Note

• If the “Subwoofer” setting is set to “No”, the “Front” setting

is fixed at “Full Band”.

■ Center

, Surround

` Full Band

` 40Hz to 80Hz(THX)

to 100Hz, 120Hz, 150Hz,

200Hz

` None

■ Front Wide

*1*2*4*6*7

, Front High

*1*2*5*6

` Full Band

` 40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz,

200Hz

` None

■ Surround Back

*2*3*8*9

` Full Band

` 40Hz to 80Hz(THX)

to 100Hz, 120Hz, 150Hz,

200Hz

` None

Note

“Full Band” can be selected only when “Full Band” is

selected in the “Front” setting.

If the “Surround” setting is set to “None”, this setting

cannot be selected.

If the “Surround” setting is set to anything other than

“Full Band”, “Full Band” cannot be selected here.

When the “Powered Zone 2” setting is set to “Yes”, this

setting cannot be selected.

When the “Powered Zone 3” setting is set to “Yes”, this

setting cannot be selected.

This setting is set automatically by

Audyssey MultEQ

XT32 Room Correction and

Speaker Setup function (➔ page 28).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR929 Seite 65

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR929

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info