Bedienungsanleitung Onkyo TX-NR929 (Seite 66 von 160) (Englisch)

517568

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

Advanced Operations

En-66

Operating

procedure

(➔ page 61)

This setting cannot be selected if the “Speakers Type

(Front)” setting is set to “Bi-Amp” or “Digital

Crossover”.

If the “11ch Playback” setting is enabled, “None” cannot

be selected.

When the “Powered Zone 3” setting is set to “Yes”

(➔ page 65) while Powered Zone 2 is enabled

(➔ page 84), this setting cannot be selected.

When the “Speakers Type(Front)” setting is set to

“Bi-Amp” or “Digital Crossover” while Powered Zone 2

is enabled (➔ page 84), this setting cannot be selected.

■ Surround Back Ch

` 1ch:

Select if only one surround back speaker L is

connected.

` 2ch

Select if two (left and right) surround back

speakers are connected.

Note

• If the “Surround Back” setting is set to “None”, this setting

cannot be selected.

■ LPF of LFE

(Low-Pass Filter for the LFE Channel)

` 80Hz, 90Hz, 100Hz, 120Hz

` Off:

Low-Pass Filter is not applied.

With this setting, you can specify the cutoff

frequency of the LFE channel’s low-pass filter

(LPF), which can be used to filter out unwanted

hum. The LPF only applies to sources that use the

LFE channel.

Note

• If you’re using THX-certified speakers, select “80Hz”.

■ Subwoofer Phase

` 0

` 180º:

Moves the subwoofer phase.

Note

• If the “Subwoofer” setting is set to “No”, this setting cannot

be selected.

■ Double Bass

` On

` Off(THX)

Turn this setting on to boost bass output by feeding

bass sounds from the front left, right, and center

channels to the subwoofer. Default setting: “

-----”

Note

• When the “Subwoofer” setting is set to “No” or the “Front”

setting to anything other than “Full Band”, this setting is

fixed to “-----”.

• This setting is set to “On” automatically when the

“Subwoofer” and “Front” settings are set for the first time

to “Yes” and “Full Band” respectively.

• If you’re using THX-certified speakers, select “Off(THX)”.

Speaker Distance

Here you can specify the distance from each speaker

to the listening position so that the sound from each

speaker arrives at the listener’s ears as the sound

designer intended.

■ Unit

` feet:

Distances can be set in feet. Range: 0.5ft to

30.0ft in 0.5 foot steps.

` meters:

Distances can be set in meters. Range: 0.15m

to 9.00m in 0.15 meter steps.

(The default setting varies from country to country.)

■ Left, Front Wide Left, Front High Left, Center,

Front High Right, Front Wide Right, Right,

Surround Right, Surround Back Right, Surround

Back Left, Surround Left, Subwoofer

` Specify the distance from each speaker to your

listening position.

Note

• Speakers that you set to “No” or “None” in

“Speaker Configuration” cannot be selected (➔ page 65).

• When the “Powered Zone 3” setting is set to “Yes”

(➔ page 65) while Powered Zone 2 is enabled

(➔ page 84), the surround back speakers cannot be used.

• When the “Speakers Type(Front)” setting is set to

“Bi-Amp” or “Digital Crossover” while Powered Zone 2 is

enabled (➔ page 84), the surround back speakers cannot

be used.

Level Calibration

Here you can adjust the level of each speaker with

the built-in test tone so that the volume of each

speaker is the same at the listening position.

■ Left, Front Wide Left, Front High Left, Center

Front High Right, Front Wide Right, Right,

Surround Right, Surround Back Right, Surround

Back Left, Surround Left

` –12.0dB to 0.0dB to +12.0dB in 0.5 dB steps.

■ Subwoofer

` –15.0dB to 0.0dB to +12.0dB in 0.5 dB steps.

This setting is NOT set automatically by

Audyssey MultEQ

XT32 Room Correction and

Speaker Setup function (➔ page 28).

This setting is set automatically by

Audyssey MultEQ XT32 Room Correction and

Speaker Setup function (➔ page 28).

This setting is set automatically by

Audyssey MultEQ XT32 Room Correction and

Speaker Setup function (➔ page 28).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR929 Seite 66

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR929

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info