Bedienungsanleitung Onkyo TX-NR929 (Seite 68 von 160) (Englisch)

517568

Zoom out

Zoom in

Vorherige Seite

1/160

Nächste Seite

Advanced Operations

En-68

Operating

procedure

(➔ page 61)

■ Preserve THX Settings

` Yes

` No

If this setting is set to “Yes”, Dynamic EQ and

Dynamic Volume have no effect in THX listening

mode.

Note

• This setting is fixed at “Yes” if “Loudness Plus” is set to

“On”.

THX Loudness Plus

THX Loudness Plus is a new volume control

technology featured in THX Ultra2 Plus™ and THX

Select2 Plus™ Certified receivers. With THX

Loudness Plus, home theater audiences can now

experience the rich details in a surround mix at any

volume level. A consequence of turning the volume

below Reference Level is that certain sound elements

can be lost or perceived differently by the listener.

THX Loudness Plus compensates for the tonal and

spatial shifts that occur when the volume is reduced

by intelligently adjusting ambient surround channel

levels and frequency response. This enables users

experience the true impact of soundtracks regardless

of the volume setting. THX Loudness Plus is

automatically applied when listening in any THX

listening mode. The new THX Cinema, THX Music,

and THX Games modes are tailored to apply the

proper THX Loudness Plus settings for each type of

content.

Digital Processing Crossover Network

Digital Crossover provides a separate routing system

by splitting the audio signal into separate frequency

bands optimized for each speaker driver. It provides a

fine, three-dimensional sound field that extend each

driver’s performance to the uppermost. With its built-

in time alignment function, this system also adjusts

the sound shifting that occurs when there is a

physical offset between sound drivers. At a digital

processing level, it corrects this offset by delaying the

related audio signal.

Although this function is meant for speakers without

crossover network, it can also be used with bi-amped

speakers.

Tip

• This setting can be done while listening to an audio source.

•Press MODE/D (Blue) to switch from the current audio

source to test noises. Pressing MODE/D (Blue) again or the

cursor buttons will stop the test noises and switch back to

the original audio source.

Note

• This setting can only be made when “Speakers Type

(Front)” is set to “Digital Crossover” (➔ page 65).

■ Crossover

` “250Hz”, “320Hz”, “400Hz”, “500Hz, “630Hz”,

“800Hz”, “1000Hz”, “1250Hz”, “1600Hz”,

“2000Hz”, “2500Hz”, “3200Hz

”, “4000Hz”,

“5000Hz”

Output Band for Test

` High + Low

, High, Low:

Select the output for the audio signal.

Tip

• Pressing MODE/D (Blue) button plays band-limited test

noises which center on the specified frequency.

• We recommend choosing a crossover value that creates no

volume difference between “High” and “Low”.

Note

• Refer to your speaker manual when setting without the use

of test noises.

■ Overlap

` No

` Yes

With this setting, a frequency band near the specified

crossover frequency is output by both tweeters and

woofers. Based on the frequency selected for

“Crossover”, the cutoff frequency of the low-pass

filter (LPF) will be set to 1/3 octave up and that of the

high-pass filter (HPF) to 1/3 octave down. Example:

With a “Crossover” of “3200Hz”, the cutoff frequency

of the woofers’ LPF will be “4000Hz”, and the

tweeters’ HPF will be “2500Hz”.

Tip

• Sounds processed by Digital Processing Crossover

Network are played.

• You can switch from the current audio source to test noises

by pressing MODE/D (Blue).

• In the case of usage of the bi-amped speakers, if there is a

difference between the crossover frequency in the

speakers’ built-in network and the crossover frequency to

be set on the AV receiver, the frequency dip may be

caused. Therefore, it is recommended that this function

should be set to “Yes”.

■ High Level, Low Level

` –6.0dB to 0.0dB

to +6.0dB in 0.5 dB steps.

With this setting, you can set the volume of tweeters

and woofers.

Tip

• Sounds processed by Digital Processing Crossover

Network are played.

• You can switch from the current audio source to test noises

by pressing MODE/D (Blue).

■ High Phase, Low Phase

` 0

` 180°:

With this setting, you can adjust the phase of tweeters

and woofers.

Cutoff frequencies of the woofers’ low-pass filter

(LPF) and the tweeters’ high-pass filter (HPF) are

set according to the frequency specified for

“Crossover”.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-NR929 Seite 68

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-NR929

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info