Bedienungsanleitung Onkyo TX-SR 505 E (Seite 65 von 72) (Englisch)

62082

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

Troubleshooting

If you have any trouble using the AV receiver, look for a

solution in this section.

Can’t turn on the AV receiver

• Make sure that the power cord is plugged into the wall

outlet properly.

• Unplug the power cord from the wall outlet, wait 5

seconds or more, then plug it in again.

The AV receiver turns off as soon as it’s turned

• The amp protection circuit has been activated.

Remove the power cord from the wall outlet immedi-

ately. Disconnect all speaker cables and input sources,

and leave the AV receiver with its power cord discon-

nected for 1 hour. After that, reconnect the power cord

and set the volume to maximum. If the AV receiver

stays on, set the volume to minimum, disconnect the

power cord, and reconnect your speakers and input

sources. If the AV receiver turns off when you set the

volume to maximum, disconnect the power cord, and

contact your Onkyo dealer.

There’s no sound or it’s very quiet

• Make sure that the digital input source is selected

properly (page 39). Press the [DIGITAL INPUT] but-

ton repeatedly.

• Make sure the speaker set A or B is on (page 6).

• Make sure that all audio connecting plugs are pushed

in all the way (page 22).

• Make sure that the polarity of the speaker cables is

correct, and that the bare wire is in contact with metal

part of each speaker terminal (page 19)

• Make sure that the speaker cables are not shorting.

• Check the volume. It can be set to MIN, 1 through 79,

or MAX (page 40). The AV receiver is designed for

home theater enjoyment and has a wide volume range

for precise adjustment.

• If the MUTING indicator is shown on the display,

press the remote controller’s [MUTING] button to

unmute the AV receiver (page 46).

• While a pair of headphones is connected, no sound is

output by the speakers (page 47).

• Check the digital audio output settings on the con-

nected device. On some games consoles, such as those

that can play DVDs, the default setting is off.

•With some DVD-Video discs, you need to select an

audio format from a menu.

• If your turntable doesn’t have a phono preamp built-in,

you must connect one between it and the AV receiver.

If your turntable uses an MC cartridge, you must con-

nect an MC head amp, or an MC transformer and a

phono preamp.

• Make sure that the speaker setup microphone is not

still connected.

• Specify the speaker distances and adjust the individual

speaker levels (page 59).

• The input signal format is set to PCM or DTS. Set it to

Auto (page 61).

For TX-SR505 North American model/

TX-SR505E/TX-SR575 with HDMI

• Audio from a DVD player connected via HDMI is not

output by the speakers connected to the AV receiver.

To listen to this audio through the speakers, in addition

to an HDMI connection, you’ll also need to make a

separate analog or digital audio connection (page 27).

• If your DVD player is connected via HDMI and your

TV produces no sound, check your DVD player’s

audio output settings, and be sure to select an audio

format that’s supported by your TV.

Only the front speakers produce sound

• When the Stereo or Mono listening mode is selected,

only the front speakers and subwoofer produce sound.

• Make sure the speakers are conﬁgured correctly

(page 56).

Only the center speaker produces sound

• If you use the Pro Logic IIx Movie, Pro Logic IIx

Music, or Pro Logic IIx Game listening mode with a

mono source, such as an AM radio station or mono TV

program, the sound is concentrated in the center

speaker.

• Make sure the speakers are conﬁgured correctly

(page 56).

The surround speakers produce no sound

• When the Stereo or Mono listening mode is selected,

the surround speakers produce no sound (page 50).

• Depending on the source and current listening mode,

not much sound may be produced by the surround

speakers. Try selecting another listening mode.

Power

Audio

If you can’t resolve the issue yourself, try resetting

the AV receiver before contacting your Onkyo dealer.

To reset the AV receiver to its factory defaults,

turn it on and, while holding down the [VCR/DVR]

button, press the [STANDBY/ON] button. “Clear”

will appear on the display and the AV receiver will

enter Standby mode.

Note that resetting the AV receiver will delete your

radio presets and custom settings.

STANDBY/ON

VCR/DVR

TX-SR505_En.book Page 65 Tuesday, January 30, 2007 11:53 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-SR 505 E Seite 65

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-SR 505 E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info