Bedienungsanleitung Onkyo TX-SR578 (Seite 62 von 72) (Englisch)

645345

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

■ There’s no picture

■ There’s no picture from a source connected to

an HDMI IN

■ The on-screen menus don’t appear

■ The picture is distorted

■ The on screen display does not appear

■ Reception is noisy, FM stereo reception is

noisy, or the FM STEREO indicator doesn’t light

■ The remote controller doesn’t work

■ Can’t control other components

Video

Make sure that all video connecting plugs are pushed

in all the way.

Make sure that each video component is properly

connected.

15, 16,

If your TV is connected to the HDMI OUT, select

“-----” in the “HDMI Input” setup to watch com-

posite video, and component video sources.

If the video source is connected to a component

video input, you must assign that input to an input

selector, and your TV must be connected to either

the HDMI OUT or COMPONENT VIDEO MONI-

TOR OUT.

16, 35

If the video source is connected to a composite video

input, your TV must be connected to the HDMI

OUT or the corresponding composite video output.

If the video source is connected to an HDMI input,

you must assign that input to an input selector, and

your TV must be connected to the HDMI OUT.

15, 35

While the Pure Audio listening mode is selected, the

video circuitry is turned off and only video signals

input through HDMI IN can be output.

—

On your TV, make sure that the video input to which

the AV receiver is connected is selected.

—

Reliable operation with an HDMI-to-DVI adapter is

not guaranteed. In addition, video signals from a PC

are not guaranteed.

When the Resolution is set to any resolution not sup-

ported by the TV, no video is output by the HDMI

outputs.

If the message Resolution Error appears on the AV

receiver’s display, this indicates that your TV does

not support the current video resolution and you

need to select another resolution on your DVD

player.

—

(European, Australian and Asian models) Specify

the TV system used in your area in the TV Format

Setup.

On your TV, make sure that the video input to which

the AV receiver is connected is selected.

—

When the AV receiver doesn’t connect TV with

HDMI, onscreen menus are not displayed.

—

(European, Australian and Asian models) Specify

the TV system used in your area in the TV Format.

Depending on the input signal, the on screen display

may not appear when the input signal from the

HDMI IN is output to a device connected to the

HDMI OUT.

Tuner

Relocate your antenna. —

Move the AV receiver away from your TV or com-

puter.

—

Listen to the station in mono. 25

When listening to an AM station, operating the

remote controller may cause noise.

—

Passing cars and airplanes can cause interference. —

Concrete walls weaken radio signals. —

If nothing improves the reception, install an outdoor

antenna.

—

Remote Controller

Before operating this unit, be sure to press

RECEIVER.

—

Make sure that the batteries are installed with the

correct polarity.

Install new batteries. Don’t mix different types of

batteries, or old and new batteries.

Make sure that the remote controller is not too far

away from the AV receiver, and that there’s no

obstruction between the remote controller and the

AV receiver’s remote control sensor.

Make sure that the AV receiver is not subjected to

direct sunshine or inverter-type fluorescent lights.

Relocate if necessary.

—

If the AV receiver is installed in a rack or cabinet

with colored-glass doors, the remote controller may

not work reliably when the doors are closed.

—

Make sure you’ve selected the correct remote con-

troller mode.

9, 58

When using the remote controller to control other

manufacturers’ AV components, some buttons may

not work as expected.

—

Make sure you’ve entered the correct remote control

code.

Make sure to set the same ID on both the AV receiver

and remote controller.

If it’s an Onkyo component, make sure that the u

cable and analog audio cable are connected properly.

Connecting only an u cable won’t work.

Make sure you’ve selected the correct remote con-

troller mode.

9, 58

If you’ve connected a cassette tape deck, to the TV/

CD IN jack, or an RI Dock to the TV/CD IN or

GAME IN or VCR/DVR IN jacks, for the remote

controller to work properly, you must set the display.

If you cannot operate it, you will need to enter the

appropriate remote control code.

To control another manufacturer’s component, point

the remote controller at that component.

To control an Onkyo component that’s connected via

u, point the remote controller at the AV receiver.

Be sure to enter the appropriate remote control code

first.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-SR578 Seite 62

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-SR578

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info