Bedienungsanleitung Onkyo TX-SR578 (Seite 64 von 72) (Englisch)

645345

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

■ When performing “Audyssey 2EQ

Room

Correction and Speaker Setup”, the

measurement fails showing the message

“Ambient noise is too high.”.

■ The following settings can be made for the

composite video inputs

You must use the buttons on the unit to make these set-

tings.

1. While holding down the input selector button for the input

source that you want to set, press SETUP.

2. Use e/r to change the setting.

3. Press the input selector button for the input source that you

want to set when you’ve finished.

• Video Attenuation

This setting can be made for the BD/DVD, VCR/DVR,

CBL/SAT, GAME, or AUX input.

If you have a games console connected to the composite

video input, and the picture isn’t very clear, you can

attenuate the gain.

Video ATT:OFF: (default).

Video ATT:ON: Gain is reduced by 2 dB.

The AV receiver can upconvert component video and

composite video sources for display on a TV connected to

the HDMI OUT. However, if the picture quality of the

source is poor, upconversion may make the picture worse

or disappear altogether.

In this case, try the following:

This can be caused by any malfunction in your

speaker unit. Check if the unit produces normal

sounds.

—

The AV receiver contains a microcomputer for signal

processing and control functions. In very rare situations,

severe interference, noise from an external source, or

static electricity may cause it to lockup. In the unlikely

event that this happens, unplug the power cord from the

wall outlet, wait at least five seconds, and then plug it

back in again.

Onkyo is not responsible for damages (such as CD

rental fees) due to unsuccessful recordings caused by

the unit’s malfunction. Before you record important

data, make sure that the material will be recorded cor-

rectly.

Before disconnecting the power cord from the wall out-

let, set the AV receiver to Standby.

Important Note Regarding Video Playback

If the video source is connected to a component

video input, connect your TV to the COMPO-

NENT VIDEO OUT.

If the video source is connected to a composite video

input, connect your TV to the MONITOR OUT V.

On the main menu, select “1. Input/Output

Assign”, and then select “2. HDMI Input”.

Select the relevant input selector, and assign it to

“-----” (➔ 35).

On the main menu, select “1. Input/Output

Assign”, and then select “3. Component Video

Input” (➔ 36):

If the video source is connected to COMPONENT

VIDEO IN 1, select the relevant input selector, and

assign it to “IN1”.

If the video source is connected to COMPONENT

VIDEO IN 2, select the relevant input selector, and

assign it to “IN2”.

If the video source is connected to composite video

input, select the relevant input selector, and assign it

to “-----”.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Onkyo TX-SR578 Seite 64

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Onkyo TX-SR578

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info