Bedienungsanleitung Pacojet 2 (Seite 20 von 29) (Englisch)

660371

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

d) Select the cutting/chopping mode on the control

panel if this has not yet been preselected. The

overpressure function is preset as the standard

default for cutting/chopping prior to each start

butcanbedeactivatedasrequiredbypressing

the “Normal pressure” button before starting the

processing cycle.

When the START button has been pressed, the PACOJET 2 will proceed

through the chosen processing cycle fully automatically. Upon completion of

the processing cycle, the shaft and the 2- or 4-blade cutter attachment re-

turn to the start position, the beaker is depressurized automatically and the

processing cycle ends.

IMPORTANT! Î

Never start the machine without having inserted a pacotizing beaker into e)

the protective outer beaker!

After the cutting/chopping procedure6.3.2

Demount the protective outer beaker containing the pacotizing beaker ac-a)

cording to the PACOJET 2 instruction manual, section 6.2.4 with the spray

guard resting in place.

Remove the spray guard with the blade cutter attachment off the pactotiz-b)

ing beaker using the three tabs.

Using the blade tongs, grasp the blade cutter attachment and remove it c)

from the spray guard. The blade cutter attachment may now be cleaned

immediately under running water. Further cleaning directions can be found

in the separate instruction manual supplied with the Pacojet Coupe Set,

which is available as an optional add-on.

d) Should no further beakers be immediately proc-

essed, a rinsing cycle of the PACOJET 2 food

processingsystemmustbeconsequentlyinitiat-

ed using the cleaning kit provided. Please clean

the machine in accordance with the instructions

found in Chapter 7.

Cutting/Chopping procedure6.3.1

a) Fill the pacotizing beaker with small pieces of

fresh, non-frozen food, then add other desired

ingredients and seasonings.

IMPORTANT! Î

Neverllthepacotizingbeakerabovethemaximumll-line.Overllingbeak-

ers can result in extensive contaminant ingress that can lead to defects and

damage.

b) Remove the 2-blade or 4-blade cutter attachment from the packaging of

the Pacojet Coupe Set by holding only the upper/connector shaft part of

thebladecutterattachment.Next,usethebladecutterafxingtongsin-

cluded to clasp the centre of the blade. The connector shaft part of the

blade cutter will face upward.

Install the spray guard on the cutter blade so that the cutter blade upper/

connector shaft goes through the hole in the spray guard. Using the cutter

tongs, bring the cutter blade and the spray guard up to the splined end of

the machine shaft. Check that the cutter blade and the spray guard are

afxedproperlybyexertinglightupwardpressure.

Now the pacotizing beaker and the protective beaker can be mounted onto c)

the machine as described in section 6.2.3b of the PACOJET 2 instruction

manual.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pacojet 2 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pacojet 2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info