Bedienungsanleitung Panasonic SC-BT100 (Seite 40 von 48) (Englisch)

61553

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

RQT9161

Troubleshooting guide

Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the solutions

indicated in the chart do not solve the problem, consult your dealer for instructions.

The following do not indicate a problem with this unit:

≥Regular disc rotating sounds.

≥Image disturbance during search.

To reset this unit Page

Power

Operation

Displays

TV screen and video

To restore the unit if it freezes

due to one of the safety

devices being activated

≥Press and hold [Í/I] on this unit for 10 seconds. (The settings remain unchanged.) —

To return all settings other

than some settings to the

factory preset

≥Select “Yes” in “Default Settings” in the Setup menu.

This returns all values in the Setup menu and the on-screen menu, except for

“Remote Control”, “On-screen Language”, “DVD-Video Ratings”, “BD-Video

Ratings” and “Speaker” to the default settings.

To return to the factory

preset

≥Reset the unit as follows:

1 Press [Í/I] on the unit to turn off the unit.

2 Press and hold [9/5], [∫] (Stop) and [< OPEN/CLOSE] on the unit at the

same time for more than 5 seconds until “PLEASE WAIT” is displayed on the unit.

3 The power is turned off automatically.

—

No power. ≥Insert the AC mains lead securely into a known active household mains socket. 9

The unit switches to

standby mode.

≥When the time set for the sleep timer has passed, the unit will be turned off.

≥

One of the unit’s safety devices is activated. Press [

/I] on this unit to turn the unit on.

—

The remote control doesn’t

work properly.

≥The remote control and this unit are using different

codes. Change the code on the remote control.

Press and hold [OK] and the indicated number

button at the same time for more than 5 seconds.

≥The batteries are depleted. Replace them with new ones.

≥You are not pointing the remote control at this unit’s remote control signal sensor

during operation.

≥Coloured glass may obstruct the signal reception/transmission.

≥Do not place the signal sensor in direct sunlight or in areas that may be subject to

sunlight exposure.

≥

It may be necessary to set the code on the remote control again after changing the batteries.

—

The unit is on but cannot be

operated.

≥Confirm the correct source is selected.

≥Some operations may be prohibited by the disc.

≥The unit is hot (“U59” appears on the display). Wait for “U59” to disappear.

≥One of the unit’s safety devices may have been activated. Reset the unit as follows:

1 Press [Í/I] on this unit to switch the unit to standby.

If the unit doesn’t switch to standby, press and hold [Í/I] on this unit for about 10

seconds. Alternatively, disconnect the AC mains lead, wait one minute, then

reconnect it.

2 Press [Í/I] on this unit to switch it on. If the unit still cannot be operated, consult

the dealer.

≥Condensation has formed: Wait 1 to 2 hours for it to evaporate.

—

Play fails to start even when

[1 PLAY] is pressed.

Play starts but then stops

immediately.

≥Insert the disc correctly with the label facing up.

≥The disc is dirty.

≥You tried to play a blank disc or unplayable disc on this unit.

≥The producers of the disc can control how discs are played. So you may not always

be able to control play as described in these operating instructions. Read the disc’s

instructions carefully.

≥[DivX[ If playing DivX VOD content, refer to the homepage where you purchased it.

14, 15

—

Cannot eject disc. ≥The unit may have a problem. While the unit is off, press and hold [:/6] and

[< OPEN/CLOSE] on this unit at the same time for about 5 seconds. Remove the

disc and consult the dealer.

—

Startup is slow.

When the unit is turned on, audio

and video output takes a long time.

It takes time before play starts.

≥Startup takes time in the following situations.

–Immediately after a power failure or the AC mains lead is connected.

–When the unit is connected with an HDMI cable.

≥

[DivX[ This is normal on DivX video.

—

Cannot set “On” in

“BD-Video 24p Output”.

≥Only when the unit is connected to the HDMI terminal of a TV supporting 24p you

can select “On”.

The display is dim. ≥Change “FL Display” in the Setup menu. 35

The elapsed time displayed

is actually less than the

playtime.

≥The displayed play time is converted from the number of frames at 29.97 frames

(equal to 0.999 seconds) to one second. There will be a slight difference between

the time displayed and the actual elapsed time (e.g., actual one-hour elapsed time

may display as approximately 59 minutes 56 seconds).

—

Picture stops. ≥[DivX[ Picture may stop if the DivX file are greater than 2 GB. —

The 4:3 aspect ratio picture

expands left and right.

Screen size is wrong.

≥Use the TV to change the aspect. Refer to your TV’s operating instructions.

≥When using an HDMI cable, set “TV Aspect” to “16:9”.

≥When using a component video cable, set “Progressive” to “Off”. If the situation is

not restored after that, set “TV Aspect” to “4:3 Pan & Scan”.

—

33, 36

e.g., Display

SC-BT100P-ENG-Body4_mst.fm Page 40 Friday, April 11, 2008 2:42 PM

Panasonic SC-BT100 Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic SC-BT100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info