Bedienungsanleitung Panasonic SC-HTB770 (Seite 33 von 44) (Englisch)

618145

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Operations

RQT9849

Depending on your preference, It is possible to

turn off the 3D surround effect and the clear-

mode dialog effect.

While pressing and holding

[SOUND] on the remote control,

press and hold [VOL r] on the main

unit for more than 4 sec.

While the setting is displayed, press

[SOUND] to change the setting.

≥ The setting changes each time [SOUND] is pressed.

≥ The indicator for the selected setting blinks for 20 sec and

then exits the setting mode.

≥ This setting will be reset to on when the main unit is turned

off.

≥ When off is selected, the dialog effect level cannot be

adjusted.

You can turn off dimmer mode and keep the LED

indicators bright.

While pressing and holding [INPUT

SELECTOR] on the remote control,

press and hold [s VOL] on the main unit

for more than 4 sec to turn off Dimmer

mode.

≥ The indicator for the current condition will turn brighter.

≥ The setting is maintained until it is changed again.

≥ Default setting of this function is on.



To turn on dimmer mode, repeat the operation above.

After performing the operation, the indicator for the current

condition will be dim.

With this function turned on, this unit can be set to

automatically switch to standby mode if there is no

signal input and no operation is performed for 2 hours.

While pressing and holding

[DIALOG LEVEL j] on the remote

control, press and hold [INPUT

SELECTOR] on the main unit for

more than 4 sec.

≥ The indicator for the current setting blinks for 20 sec.

While the indicator is blinking,

press [DIALOG LEVEL j] to change

the setting.

≥ The setting changes each time [DIALOG LEVEL j] is

pressed.

≥ The setting is maintained until it is changed again.

∫ Remote control code

When other Panasonic devices respond to this

system’s remote control, change the remote control

code on this system and the remote control.

Preparation

≥ Turn off all other Panasonic products.

≥ Turn on the main unit.

Change the remote control code to code 2:

1 Aim the remote control at the main unit’s

remote control sensor.

2 Press and hold [MUTE] and [ ] on the

remote control for more than 4 sec.

≥ All the indicators will blink for 10 sec when the

code of this system is changed.

≥ The setting is maintained until it is changed again.



≥ If the main unit does not operate after changing the code,

repeat steps 1 and 2.

≥ To change the remote control code to code 1, repeat the

steps above, but replace [ ] with [INPUT SELECTOR].

Using the Dolby Virtual

Speaker effect

“STANDARD” indicator blinks:

3D surround effect and clear-mode

dialog effect is on.

“STEREO” indicator blinks:

3D surround effect and clear-mode

dialog effect is off.

Dimmer mode

Auto standby function

“STANDARD” indicator blinks:

Auto standby function is on.

“STEREO” indicator blinks:

Auto standby function is off.

Others

SC-HTB770_RQT9849-B_mst.book 33 ページ２０１３年２月２５日　月曜日　午前１１時５３分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic SC-HTB770 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic SC-HTB770

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info