Bedienungsanleitung Panasonic SCALL30TEG (Seite 29 von 40) (Englisch)

612774

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Reference

SQT0936

≥ When the HDMI connections are changed,

after a power failure or after the AC mains

lead has been removed, VIERA Link

operations may not function properly.

jTurn on all the devices that are connected to

the TV with an HDMI cable and then turn the

TV on.

jTurn off the VIERA Link settings of the TV

and turn it on again. For details refer to the

operating instructions for the TV.

jWhile the main unit and the TV are

connected with the HDMI cable, turn on the

TV and then remove the main unit’s AC

mains lead and reconnect it again.

The first few seconds of audio cannot be

heard when using the HDMI connection.

This may occur during DVD-Video chapter

playback. Change the digital audio output

setting on the connected device from

“Bitstream” to “PCM”.

When operating an HDMI compatible device

of a different brand, the main unit reacts in

an unwanted manner.

HDAVI Control commands may use a different

signal depending on the brand of the device. In

this case, turn VIERA Link off. (> 23)

When the main unit is turned on or off, audio

and video are temporarily disabled.

When the main unit is turned on or off it is

normal for the audio and video to be temporarily

disabled. This is not a malfunction. This can

occur when the device it is connected to, via

HDMI, does not support Panasonic’s VIERA

Link feature (HDAVI Control 3 or later).

The images from this system do not appear

on the TV.

When outputting in 60p (4K), images may be

distorted depending on the HDMI cable. Use

High Speed HDMI cables which support

18 Gbps bandwidth.

Pairing cannot be done.

Check the Bluetooth

device condition.

The device cannot be connected.

≥ The pairing of the device was unsuccessful or

the registration has been replaced. Try pairing

the device again. (> 19)

≥ This system might be connected to a different

device. Disconnect the other device and try

pairing the device again.

The device is connected but audio cannot be

heard through this system.

For some Bluetooth

devices, you have to set

the audio output to “SC-ALL30T” manually.

Read the operating instructions for the device

for details.

Connection is interrupted.

Sound is interrupted/sound skips/there is a

lot of noise.

≥ Remove any obstacle between the main unit

and the device.

≥ Other devices that use the 2.4 GHz frequency

band (wireless router, microwaves, cordless

phones, etc.) are interfering. Bring the

Bluetooth

device closer to the main unit and

distance it from the other devices.

≥ Select “MODE 1” for stable communication.

(> 23)

If the above does not fix the problem, you may

be able to fix the problem by reconnecting this

unit and the Bluetooth

device.(> 20)

The One-Touch Connection (NFC feature) is

not working.

≥ Make sure the main unit and the NFC feature

of the device are turned on. (> 20)

≥ Change the touch location of the Bluetooth

device or main unit and then touch the NFC

touch area again.

Bluetooth

SC-ALL30T-SQT0936.book 29 ページ２０１５年４月２８日　火曜日　午前１０時０分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic SCALL30TEG Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic SCALL30TEG

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info