Bedienungsanleitung Panasonic SCHC49EG (Seite 13 von 84) (Englisch, Spanisch, Polnisch)

608423

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

RQT9886

ENGLISH

When other Panasonic equipment responds to the

supplied remote control, change the remote control

code.

1 Press [CD/RADIO] to select “CD”.

2 While pressing and holding [SELECTOR] on the

unit, press and hold [CD/RADIO] on the remote

control until the unit’s display shows “REMOTE 2”.

3 Press and hold [OK] and [CD/RADIO] on the

remote control for at least 4 seconds.



≥

To change the mode back to “REMOTE 1”, press [CD/RADIO]

to select “CD” and then repeat the step 2 and 3 but replace

[CD/RADIO] with [ ].

Occasionally, Panasonic may release updated

software for this unit that may add or improve the way

a feature operates. These updates are available free of

charge.

For more details, refer to the following website.

http://panasonic.jp/support/global/cs/

(This site is in English only.)

∫ Checking the software version

The version of the installed software is displayed.

Press [SETUP] repeatedly to select “SW VER.” and

then press [OK].

≥ Press [OK] to exit.

Troubleshooting

Before requesting service, make the following checks.

If you are uncertain about some of the check points, or

if the solutions indicated in the following guide does not

resolve the issue, then consult your dealer for

instructions.

Humming heard during playback.

≥ If an AC mains lead or fluorescent lights are near the cords, then

keep other appliances and cords away from the cables.

The unit does not work.

≥ One of the unit’s safety devices may have been activated.

Reset the unit as follows:

1 Press [Í/I] on the unit to switch the unit to standby.

≥ If the unit does not switch to standby, press [Í/I] on the unit

for approximately 10 seconds. The unit is forcibly switched

to standby. Alternatively, disconnect the AC mains lead, wait

for at least 3 minutes, then reconnect it.

2 Press [Í/I] on the unit to switch it on. If the unit still cannot be

operated, consult the dealer.

MP3 cannot be read.

≥ You may not be able to play MP3 if you have copied a

multi-session disc that has no data between sessions.

≥ When creating a multi-session disc, it is necessary to close the

session.

≥ The amount of data on the disc is too small. Set the amount of

data to above 5 MB.

The remote control does not work properly.

≥ The battery is depleted or inserted incorrectly. (l 4)

Incorrect display or play does not start.

≥ Make sure that the disc is compatible with this unit. (l 16)

≥ There is moisture on the lens. Wait for about an hour and then try

again.

Changing the unit and remote

control code

Software update

To return all settings to the factory defaults

When the following situations occur, reset the

memory:

≥ There is no response when buttons are pressed.

≥ You want to clear and reset the memory contents.

1 Disconnect the AC mains lead. (Wait for at least

3 minutes before proceeding to step 2.)

2 While pressing and holding down [Í/I] on the

unit, reconnect the AC mains lead.

≥ Keep holding down [Í/I] until “---------” appears on the

display.

3 Release [Í/I].



≥ All the settings are returned to the factory defaults. You will

need to reset the memory items.

General

Remote control

Disc

SC-HC49EG~RQT9886-R.book 13 ページ２０１４年４月３日　木曜日　午前９時２９分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic SCHC49EG Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic SCHC49EG

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info