Bedienungsanleitung Panasonic SCHC57DBEB (Seite 20 von 28) (Englisch)

612856

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

RQT9709

Occasionally, Panasonic may release updated

software for this unit that may add or improve the way

a feature operates. These updates are available free of

charge.

Preparation

Connect this unit to the wireless network. (> 11)

≥ Make sure that the wireless network is connected to the

Internet.

1 Press [SETUP] repeatedly to select

“SW UPDATE” and then press [OK].

2 Press [3, 4] to select “UPDATE? Y” and then

press [OK] to start the update.

{. After the update has finished, “SUCCESS” is displayed.

3 Disconnect the AC mains lead and reconnect it

after 3 minutes.

≥ DO NOT DISCONNECT the AC mains lead while one of

the following messages is displayed.

– “LINKING”, “UPDATING” or “%”

(“  ” stands for a number.)



≥ If you do not want to update the unit, select “UPDATE? N”

and then press [OK] in step 2.

≥ If there are no updates, “NO NEED” is displayed after step 2.

≥ During the update process, no other operations can be

performed.

≥ Downloading will require several minutes. It may take

longer or may not work properly depending on the

connection environment.

∫ Checking the software version

1 Press [SETUP] repeatedly to select “SW VER.” and then

press [OK].

{. The version of the installed software is displayed.

2 Press [OK] to exit.

To check the Wi-Fi

signal strength where the unit is

located.

Preparation

Connect this unit to the wireless network. (> 11)

1 Press [SETUP] repeatedly to select “SIG.LEVEL”

and then press [OK].

≥ The unit’s display shows “LEVEL ”.

(“  ” stands for a number.)

2 Press [OK] to exit this display mode.



≥ It is recommended to have a signal strength of “3”. Change

the position or angle of your wireless network router or the

unit if the indication is “2” or “1” and see if the connection

improves.

≥ If “LEVEL 0” is displayed, this unit cannot establish a link with

the wireless network router. (> 22)

≥ This function does not work when AirPlay is used.

This unit can turn on automatically from standby mode

when this unit is selected as the AirPlay speakers.

Preparation

Connect this unit to the wireless network. (> 11)

1 Press [SETUP] repeatedly to select “NET STNBY”

and then press [OK].

2 Press [3, 4] to select “ON” and then press [OK].



≥ To cancel this function, select “OFF” in step 2.

≥ The factory preset is “OFF”. If this function is set to “ON” the

standby power consumption will increase.

To check the unit’s IP/MAC address.

1 Press [CD] to select “CD”.

2 Press and hold [s WPS] on the unit and [4] on

the remote control until the unit’s display shows

the IP address.

{. The IP address is partially displayed.

≥ To display the MAC address on the unit, repeat the

steps above by replacing [4] with [3].

3 Press [3, 4] on the remote control to show the

rest of the IP address.



≥ Be sure to remove the disc from the disc tray when checking

the address.

≥ The “ – ” displayed on the top or bottom left of the display

indicate the first and last units respectively.

Software update

Wi-Fi

signal strength

Network standby

IP/MAC Address

SC-HC57DB~RQT9709-1B.book Page 20 Friday, March 2, 2012 3:31 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic SCHC57DBEB Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info