Bedienungsanleitung Panasonic SCHT1000PP (Seite 48 von 56) (Englisch)

613117

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

RQT7061

INFO

Troubleshooting guide

Before requesting service, make the below checks. If you are in doubt about some of the check points, or if the remedies indicated in the chart do

not solve the problem:

In the U.S.A., contact the Panasonic Customer Call Center at 1-800-211-7262, or e-mail consumerproducts@panasonic.com,

or the website (http://www.panasonic.com).

In Canada, contact the Panasonic Canada Inc. Customer Care Centre at 1-800-561-5505, or visit the website (www.panasonic.ca),

or an authorized Servicentre closest to you.

Power Page

Operation

Remote control

Picture

≥When progressive output is on, refer also to “Progressive video” below.

Progressive video

No power. ≥Insert the AC power supply cord and system cable securely. Setup

Guide

The unit switches to the standby

mode.

≥This is a power saving feature. You can turn it off if you would prefer (Set Up—Off Timer—Off).

Press [Í POWER] to turn the unit on.

≥One of the unit’s safety devices may have activated. Press [Í POWER] to turn the unit on.

—

The unit is on but cannot be

operated.

≥Some operations may be prohibited by the disc.

≥The unit is hot (“U14” appears on the display). Wait for “U14” to disappear.

≥One of the unit’s safety devices may have activated.

Reset the unit as follows:

1Press [Í POWER] to switch the unit to standby.

If the unit doesn’t switch to standby, press and hold [Í POWER] for about 10 seconds.

The unit is forcibly switched to standby.

Alternatively, disconnect the AC power supply cord, wait one minute, then reconnect it.

2Press [Í POWER] to turn the unit on.

—

During disc operation the unit

does not respond.

≥The selector has been set to “FM” or “AM”. Press [DVD] to select “DVD/CD” as the source. —

The remote control doesn’t

work.

≥[HOME THEATER, TV] is not switched to “HOME THEATER”. Switch to “HOME THEATER”

when operating this unit.

≥The remote control and main unit are using different codes. Change the code on the remote

control or main unit.

≥The batteries are depleted. Replace them with new ones.

≥Point the remote control at the remote control sensor on the main unit.

≥Remove obstacles from between the remote control and main unit.

—

Cannot operate the television. ≥Change manufacturer code. Some televisions cannot be operated even if you change the

code.

≥[HOME THEATER, TV] is not switched to “TV”. Switch to “TV” when selecting the receiving

channel for the television.

The images from this unit do not

appear on the television.

≥Make sure that the television is connected to the VIDEO OUT terminal, S-VIDEO OUT

terminal or COMPONENT VIDEO OUT terminals on this unit.

≥Make sure that the television’s input setting (e.g., VIDEO 1) is correct.

≥You have set “TV Type” to “Aspect 4:3 & 480P” or “Aspect 16:9 & 480P” in the TV Screen

menus, but the television isn’t compatible with progressive signals. Press and hold [∫] and

[TIME SLIP] on the unit at the same time for about 5 seconds. The setting will change to

interlace.

Setup

Guide

—

Television reception worsens

after connecting the unit.

≥This can occur because the signals are being divided between the unit and the television.

It can be solved by using a signal booster, available from audio-visual suppliers. Consult your

dealer if reception does not improve.

—

Screen size is wrong. ≥Check the settings on your television.

≥Check the settings for “TV Type”, “4:3 TV Settings for DVD-Video” or “4:3 TV Settings for

DVD-RAM” in the TV Screen menu.

—

11, 39

On-screen messages do not

appear.

≥Go to the Display menu and select “Automatic” for “Status Messages”.

≥Press [STATUS] to show the on-screen messages constantly.

The blue background does not

appear.

≥Go to the Display menu and select “On” for “Blue Background”. 39

There is ghosting. ≥Change the settings for “3D NR”, “Block NR”, and “Mosquito NR” to “0” or turn “MPEG-DNR”

off if it is on.

Play stops for a moment during

Quick View.

≥Play may stop where two play lists join, but this is not a malfunction. —

There is ghosting when

progressive output is on.

≥Set “Progressive” to “OFF”. This problem is caused by the editing method or material used on

DVD-Video, but should be corrected if you use interlace output.

There is no apparent change in

picture quality when adjusted

with the Video menu in the on-

screen menus.

≥The effect is less perceivable with some types of video. —

7061en.book 48 ページ２００３年６月１６日　月曜日　午前１０時１２分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic SCHT1000PP Seite 48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info