Bedienungsanleitung Parkside IAN 275681 PDBS 6.2 A1 (Seite 36 von 41) (Französisch)

745541

Zoom out

Zoom in

Vorherige Seite

1/41

Nächste Seite

37 GB

General safety rules General safety rules / Before use / Start-up

because the risk from vibration is generally gr

eater

when the grip force is higher.

Additional safety instructions

for pneumatic power tools

Air under pressure can cause severe injury:

– always shut oﬀ air supply, drain hose of air

pressure and disconnect tool from air supply

when not in use, before changing accessories

or when making repairs;

– never direct air at yourself or anyone else.

Whipping hoses can cause severe injury. Always

check for damaged or loose hoses and ﬁttings.

Cold air shall be directed away from hands.

Whenever universal twist couplings (claw cou-

plings) are used, lock pins shall be installed

and whipcheck safety cables shall be used

to safeguard against possible hose-to-tool or

hose-to-hose connection failure.

Do not exceed the maximum air pressure stated

on the tool.

Never carry an air tool by the hose.

General safety

instructions for compressed

air metal shears

Always wear safety gloves.

Be careful whilst working with the shears. Edges

created on the work piece can cause cuts.

If possible, already run the shears at full speed

when applying them. Otherwise sudden, jerky

movement could result if the shears catch when

starting up at the front, resulting in backlash.

Before use

Installation

The device itself is fully functional at delivery. You

will need to install a coupler before using the de-

vice itself (please note the data speciﬁed under

technical details for accuracy of ﬁt/size).

Wrap the coupler with Teﬂon tape (not included)

before screwing it into the compressed air unitn.

Wrap the tape as tightly as possible around

the thread. This will minimise the likelihood of

air leaking and optimise the work process.

Now screw the coupling into the compressed

air equipment.

Tighten the coupler into the compressed air unit

with a size 14 spanner using moderate force

(see Fig. A).

Adjusting the compressed air supply and

connections

Only use ﬁltered, lubricated and regulated com-

pressed air.

Apply the connection method on the compressed

air unit shown in Fig. B. This will increase the ef-

fectiveness and life of the tool.

Set your compressor to the device‘s operating

pressure speciﬁed under Technical Data. Please

note, on average the pressure for 10 m of hose

will decrease by about 0.5 bar.

Excessive pressure is dan-

gerous! Never exceed the speciﬁed pressure!

Add a few drops of oil for compressed air tools

or SAE 10–20 motor oil to the compressed air

onnection of the compressed air unit. Using othe

oil (esp. viscous) will result in malfunctions, dam-

age or even total loss of the device.

Start-up

Connecting the

compressed air tool

Verify the work piece is properly secured.

Connect the compressed air by pushing on the

coupler of the hose with some force (see Fig. C).

Verify the air hose is properly seated (see Fig. D).

A loose hose whipping about out of control pre-

sents a major hazard. The coupler must be tightly

seated for the same reason. Also check this.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 275681 PDBS 6.2 A1 Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside IAN 275681 PDBS 6.2 A1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info