Bedienungsanleitung Parkside IAN 285818 PDMFG 180 A1 (Seite 28 von 135) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

746155

Zoom out

Zoom in

Vorherige Seite

1/135

Nächste Seite

PDMFG 180 A1

│

25 ■

■ Keep work area clean and well lit. Cluttered or

dark areas invite accidents. This enables better

control of the tool in unexpected situations.

WARNING!

► Have your power tool serviced by qualiﬁed

trained personnel using only original spare

parts. This ensures that the safety of the tool

is maintained.

■ Keep children and other persons away from the

tool during operation. Distractions can cause

you to lose control.

■ Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewel-

lery or long hair can be caught in moving parts.

■ Put the trigger and the tool away in the case of

an unexpected stoppage of the compressor.

■ Wherever possible, use a condensate separator

or drain the condensate (water) from the hoses

and tubing regularly before and during the use

of the compressed air tools.

■ NOTICE! An undersized compressed air system

will reduce the eﬃciency of your tool.

■ Please ensure that you have read and under-

stood the safety instructions regarding multiple

hazards before installation, operation, repair,

service and replacement of any accessories

and before work near the automatic screw-

driver. Otherwise, there is a risk of serious physi-

cal injuries.

■ The automatic screwdriver should only be ﬁtted,

adjusted or used by qualiﬁed and trained

operators.

■ The automatic screwdriver may not be modiﬁed.

Modiﬁcations can reduce the eﬀectiveness of

the safety measures and increase the risks for

the operator.

■ Do not lose the safety instructions – hand them

to the operator.

■ Never use a damaged automatic screwdriver.

■ The machines must be serviced regularly to

check whether the rated values and markings

required in the present part of ISO 11148 are

appended legibly on the machine. The em-

ployee/operator must contact the manufacturer

to obtain replacement stickers for labelling if this

is necessary.

Hazards caused by ﬂying parts

■ If a workpiece or one of the accessory parts or

even the machine tool itself breaks, parts can

be thrown oﬀ at high speeds.

■ Always wear impact-resistant safety goggles

during operation, when replacing accessory

parts or during repair or maintenance work.

The level of the required protection must be

evaluated separately for each individual task.

■ You must ensure that the workpiece has been

securely ﬁxed in place.

■ Check regularly that the rotation speed of

the compressed air tool is not higher than the

speciﬁed rotation speed appended on the

compressed air tool. These rotation speed tests

must be conducted without any accessory tools

attached.

■ Ensure that sparks and fragments created

during work do not present any hazards.

■ Separate the compressed air tool from the

compressed air supply before replacing the

attachment or accessories or before you adjust

the settings, service or clean the tool.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 285818 PDMFG 180 A1 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info