Bedienungsanleitung Parkside IAN 292167 PDSS 16 A1 (Seite 20 von 90) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

746866

Zoom out

Zoom in

Vorherige Seite

1/90

Nächste Seite

PDSS 16 A1

│

17 ■

■ The permissible speed of the accessory tool

used must be at least as high as the maximum

speed speciﬁed for the compressed air tool. Ac-

cessories that rotate faster than the permissible

rate can break and throw pieces into the air.

■ Wear a safety helmet for overhead work.

■ The tool will run on after the compressed air

tool has been switched oﬀ.

■ Ensure that no hazard is caused by sparks cre-

ated during use. Explosive or ﬂammable dusts

can be generated when processing certain

materials. There is a risk of explosion or ﬁre.

Hazards caused by repetitive move-

ments

■ Users of the compressed air tool may experi-

ence unpleasant sensations in their hands, arms,

shoulders, neck area or other body parts.

■ Assume a comfortable position when working

with the compressed air tool, pay attention to

safe footing and avoid unfavourable positions

or such that make it diﬃcult to keep your bal-

ance. During work over longer periods, the

operator should change posture to avoid dis-

comfort and fatigue.

■ If the operator notices symptoms such as persis-

tent discomfort, throbbing, pain, tingling, burning

or stiﬀness, these warning indications should not

be ignored. The operator should consult a quali-

ﬁed medical doctor.

Hazards caused by accessories

■ Separate the compressed air tool from the com-

pressed air supply before replacing the attach-

ment or accessory.

■ Only use accessories that are intended for this

appliance and comply with the requirements

and speciﬁcations listed in these operating

instructions.

■ Avoid direct contact with the accessory tool

during and after use because it may be hot or

have sharp edges.

■ The permissible speed of the accessory tool

used must be at least as high as the maximum

speed speciﬁed for the compressed air tool. Ac-

cessories that rotate faster than the permissible

rate can break and throw pieces into the air.

■ Never ﬁt a grinding disc, cutting disc or milling

cutter. A bursting grinding disc can lead to seri-

ous injuries or death.

■ Do not use discs that are damaged, cracked or

have been dropped.

■ Only approved accessory tools with the appro-

priate shaft diameter may be used.

■ Observe the manufacturer's recommendation

for small grinding tools. The maximum permissi-

ble protrusion (L0 = length of the shaft between

the collet chuck end and the small grinding

tool) speciﬁed by the manufacturer must not be

exceeded when using small grinding tools! If

the protrusion (L0) is increased, the permissible

rotation speed must be lowered. Wherever pos-

sible, insert the complete length of the shaft of

the accessory tool into the collet chuck. Ensure

that the clamping length (Lg) is at least 10 mm.

■ The shaft diameter of the accessory tool must

exactly match the clamp bore of the collet

chuck!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 292167 PDSS 16 A1 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info