Bedienungsanleitung Parkside IAN 311314 PGI 1200 A1 (Seite 11 von 48) (Deutsch, Englisch, Holländisch, Französisch)

749335

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

6GB/IE/NI

Flashes 3 x per interval Overload protection

switches on

Flashes 4 x per interval Short circuit

The socket (8) can be used again after the overload protection

has been triggered once the engine has been switched oﬀ and

restarted (See “Turning oﬀ engine” and “Starting engine”).

ATTENTION! If this happens reduce the amount of electrical

output which you are extracting from the generator or remove

defective devices which are attached.

ATTENTION! Faulty overload switches should only be re-

placed with identically constructed overload switches with the

same performance data. Please use our customer service de-

partment.

ATTENTION! Turn the device oﬀ immediately and contact

your Service Station:

• With unusual vibrations or noises.

• If the engine seems overloaded or has backﬁred.

9. Maintenance

Before cleaning and maintenance work, turn oﬀ the engine and

pull the spark plug connector (15) out of the spark plug (16).

WARNING! Risk of burning! Wait until the machine has

cooled down before cleaning or servicing it.

Air ﬁlter (Fig. 4)

Also refer to the service information.

Clean the air ﬁlter (12) regularly, and if necessary exchange it.

• Open the air ﬁlter cover (11) by removing the 2 Phillips head

screws M6x16 mm.

• Remove the ﬁlter element (12).

• When cleaning the element do not use any strong cleaners

or petrol.

• Clean the element by tapping it on a ﬂat surface. If it is very

dirty wash with soapy water, rinse with clean water and

leave to dry.

• Put it back together in the opposite order.

Spark plug (Fig. 6)

Check the spark plug (16) after the ﬁrst 20 hours of use for dirt

and if necessary clean it with a copper wire brush. Then service

the spark plug after every 50 hours of use.

• Remove the spark plug connector (15) with a turning move-

ment.

• Remove the spark plug (16) with the spark plug socket (D)

included.

• Put it back together in the opposite order.

Note: alternative spark plugs to

Bosch UR3AC

Petrol ﬁlter (Fig. 7)

Note: The petrol ﬁlter (18) is a ﬁlter bowl located directly under

the petrol cap (2) , ﬁltering any petrol added.

• Turn the on /o ﬀ switch (6) to the “OFF“ position.

• Open the petrol cap (2)

• Remove the petrol ﬁlter (18) and clean in a nonﬂammable

solvent or solvent with a high ﬂash point.

• Reinsert petrol ﬁlter (18).

• Close the petrol cap (2).

Changing the oil, (Fig. 5)

Changing the oil should take place when the engine is warm.

WARNING! Drain fuel before replacing the oil.

Only use engine oil (15W-40).

• Place the generator on its front side on a suitable surface.

• Open the oil ﬁller cap (13) and drain the warm engine oil

into a container by tilting the generator.

• Pour in engine oil (approx. 0.25 litres).

• Close the oil ﬁller cap (13).

• Stand the generator upright again.

Low oil switch oﬀ

The low oil switch-oﬀ responds, if there is not enough engine oil.

The oil check bulb (5) starts to ﬂash when there is insuﬃcient

oil in the motor. The check bulb begins to ﬂash when the oil

amount has gone below the safe level. The engine will turn oﬀ

independently after a short time. Restart is possible only after

pouring in more engine oil (see Chapter “Replacing the oil”).

10. Cleaning

Keep the safeguards, air vents and the engine housing as dust

and dirt free as possible. Wipe the device with a clean cloth

or blow it with compressed air with low pressure. We recom-

mend that you clean the device after every use. Regularly clean

the device with a damp cloth and a little soft soap. Do not

use any cleaning products or solvents which could attack the

plastic part of the device. Ensure that no water can penetrate

the housing.

11. Storage

Preparation for storage

• Empty the petrol tank with a petrol suction pump.

Warning notice: Do not remove fuel in closed rooms,

close to ﬁre or whilst smoking. Vapours can cause explo-

sions or ﬁres.

• Start the engine and leave it running until the rest of the pet-

rol has been used up.

• Change the oil after each season. To do this, remove the old

oil from the warm engine and reﬁll with new oil.

• Remove the spark plug. Fill about 20 ml of oil into the cylin-

der using an oil can.

• Slowly pull the express start so that the oil protects the cylin-

der from the inside.

• Screw the spark plug back in

• Store the device in a well ventilated place or area.

12. Transport

Preparation for transporting

• Empty the petrol tank with a petrol suction pump or alterna-

tively using the petrol tap and a suitable canister.

• Once it is ready for use, leave the engine running until the

rest of the petrol has been used up.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 311314 PGI 1200 A1 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info