764032
37
Zoom out
Zoom in
Vorherige Seite
1/132
Nächste Seite
36 GB/IE
¾Before operating the product, check whether
the accessory tool is correctly positioned, i.e.
centred in the chuck 1.
¾Screw bits are labelled according to their
dimensions and their shape. If you are
uncertain, always check whether the bit fits
tightly in the screw head without any free
play.
Working instructions
Torque
¾Smaller screws/bits can be damaged if you
set the torque or rotational speed too high.
Hard screw joints (in metal)
¾Particularly high torque occurs, for example
in metal screw joints made using drive
sockets. Select a low rotational speed.
Soft screw joints (e.g. in soft wood)
¾Again, use a low rotational speed, e.g. to
avoid damaging the surface of the wood
upon contact with the screw head. Use a
countersink.
Drilling in wood, metal and other
materials
¾Use a high speed for drill bits with small
diameter and a low speed for drill bits with
large diameter.
¾Select a low speed for hard materials and a
high speed for soft materials.
¾Secure or fasten the workpiece in a clamp or
vice (if possible).
¾Mark the spot where you want to drill
using a centre punch or nail. Select a low
rotational speed when starting.
¾Pull the rotating drill bit from the hole
repeatedly to remove dust and chips and
clear the hole.
Drilling in metal
¾Use a metal drill (HSS). For optimum results,
cool the drill bit with cooling lubricant
(cutting oil). Metal drill bits can also be
used to drill into plastics. Start with a 3 mm
diameter drill bit and then increase the size
until the desired hole diameter is achieved.
Drilling in wood
¾Use a wood drill with a lathe centre.
Deep holes: Use an auger bit.
Large-diameter holes: Use a Forstner bit.
Small screws can be screwed directly into
soft wood.
Belt clip
m CAUTION! RISK OF INJURY!
uBefore hanging the product in the belt:
Push the rotation direction switch 5 to
the centre position (lock). This prevents
the product from being switched on
accidentally.
¾The belt clip 9 allows the tool to be hooked
on belt or pocket.
Cleaning and care
m WARNING!
Always switch the product off, remove
the battery pack
10
and let the
product cool down before performing
inspection, maintenance and cleaning
work!
37

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Parkside PABSP 20-Li B2 - IAN 322691 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info