Bedienungsanleitung Parkside PDFW 120 A2 - IAN 353549 (Seite 10 von 65) (Englisch)

762964

Zoom out

Zoom in

Vorherige Seite

1/65

Nächste Seite

PDFW 120 A2

■ 6 │ GB│IE│NI│CY

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to

control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions, tak-

ing into account the working conditions and

the work to be performed. Use of the power

tool for operations diﬀerent from those intended

could result in a hazardous situation.

h) Keep handles and grasping surfaces dry,

clean and free from oil and grease. Slippery

handles and grasping surfaces do not allow

for safe handling and control of the tool in unex-

pected situations.

5. Service

a) Have your power tool serviced by a qualiﬁed

repair person using only identical replace-

ment parts. This will ensure that the safety of

the power tool is maintained.

CAUTION!

► When using power tools, note the following

basic safety precautions to protect yourself

against electrical shock, injury and ﬁre

hazards.

► Read all these instructions before using this

power tool and store the safety instructions in

a safe place.

Safety instructions for bench

grinders

a) Never use damaged accessory tools. Check

accessory tools such as grinding discs before

each use for chips or cracks and wire brushes

for loose or broken wires. When you have

checked and inserted the accessory tool,

ensure that you and any other people in the

vicinity remain outside of the range of the

rotating accessory tool and allow the tool to

rotate at maximum speed for one minute.

Damaged accessory tools usually break during

this test period.

b) The maximum permissible speed of the

accessory tool used must be at least as high

as the maximum speed speciﬁed for the

power tool. Accessories which rotate faster

than the maximum permissible rate can break

and throw pieces into the air.

a) Be aware that brushes can lose wire bristles

even during ordinary operation. Do not

overstress the wires by applying excessive

pressure to the brush. Flying wire bristles can

easily penetrate light clothing and/or skin.

d) Never grind using the edge of the grinding

disc. Grinding with the edge can cause

grinding discs to break and ﬂy apart.

■Before every use, make sure that the grinding

discs are in a usable condition. Also carry out

a sound test to detect cracks. This is done by

gently tapping the disc with a non-metallic ham-

mer to the right and left of the vertical centre

line. The taps should cause a light “ringing

sound”. If the resulting sound is dull, the disc

should not be used.

■ Change the grinding wheel if the spark

deﬂectors can no longer be set to the required

distance of max. 2 mm from the grinding wheel.

■ Use the power tool only with accessory tools

mounted on both spindles. This prevents any

accidental contact with the rotating spindle.

■ Always use the protective cover, the tool rest,

the viewing window and the spark deﬂector as

required depending on the accessory tool used.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PDFW 120 A2 - IAN 353549 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside PDFW 120 A2 - IAN 353549

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info