Bedienungsanleitung Parkside PDFW 120 A2 - IAN 353549 (Seite 18 von 65) (Englisch)

762964

Zoom out

Zoom in

Vorherige Seite

1/65

Nächste Seite

PDFW 120 A2

■ 14 │ GB│IE│NI│CY

Fitting tools onto the ﬂexible shaft

♦ Push the black collar all the way back onto

the ﬂexible shaft to lock the spindle. Note

that the collet chuck mount is loosened in an

anticlockwise direction. Hold the black collar

in this position.

♦ Use the combination spanner to undo the

collet chuck mount on the ﬂexible shaft .

♦ Fit the tool and screw the collet chuck mount

back into place.

♦ Release the black collar .

Changing the collet chuck

You can change the collet chuck if the shaft

diameter of the tool you want to use is diﬀerent.

♦ Push the black collar all the way back onto

the ﬂexible shaft to lock the spindle. Note

that the collet chuck mount is loosened in an

anticlockwise direction. Hold the black collar

in this position.

♦ Use the combination spanner to undo the

collet chuck mount on the ﬂexible shaft .

Unscrew the collet chuck mount .

♦ Remove the collet chuck and replace it with

a collet chuck with the desired diameter.

♦ Replace the collet chuck mount back on the

ﬂexible shaft . Screw the collet chuck mount

tight using the combination spanner .

♦ Release the black collar .

Using the work arbor for cutting discs

♦ Use the screw driver side of the combination

spanner to undo and tighten the screw of the

work arbor for cutting discs .

♦ Fit the work arbor for cutting discs as

described into the ﬂexible shaft .

♦ Use the combination spanner to undo the

screw on the work arbor for cutting discs .

♦ Fit the desired cutting disc / onto the screw

between the two washers.

♦ Use the combination spanner to tighten the

screw on the work arbor for cutting discs .

Use the work arbor for polishing felts

♦ Screw the tip of the work arbor for polishing

felts clockwise into the corresponding hole

in the polishing felts / .

♦ Fit the work arbor for polishing felts as

described into the ﬂexible shaft .

Using the work arbor for abrasive belts

♦ Push the required abrasive belt / com-

pletely onto the corresponding work arbor for

abrasive belts / .

♦ Use the combination spanner to tighten the

screw on the work arbor / to fasten the

abrasive belts.

♦ Fit the work arbor for abrasive belts / as

described into the ﬂexible shaft .

Notes on working with materials/

tools/speed range

■ Never use the appliance for other purposes

and only use original parts/accessories. Using

attachments or accessory tools other than those

recommended in the operating instructions can

lead to a risk of injury.

■ Determine the rotational speed range for work-

ing on zinc, zinc alloys, aluminium and copper

by trying it out on test pieces.

■ Use a low rotational speed for work on plastics

and materials with a low melting point.

■ Use a high rotational speed for working on

wood.

■ Carry out cleaning, polishing and buﬃng work

in the medium speed range.

The following are recommendations only and not

binding. When carrying out practical work, carry

out your own tests to see which tool and which set-

tings are ideal for the material you are working on.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PDFW 120 A2 - IAN 353549 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside PDFW 120 A2 - IAN 353549

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info