Bedienungsanleitung Parkside PDFW 120 A2 - IAN 353549 (Seite 17 von 65) (Englisch)

762964

Zoom out

Zoom in

Vorherige Seite

1/65

Nächste Seite

PDFW 120 A2 GB│IE│NI│CY │ 13 ■

♦ Switch the appliance on by pressing the

ON/OFF switch .

♦ Set a speed suitable for the work using the

speed control .

♦ Switch the appliance oﬀ by pressing the

ON/OFF switch again.

Grinding

♦ Place the workpiece on the tool rest .

Guide the workpiece slowly towards the

grinding disc at the required angle until the

workpiece and the grinding disc come into

contact with each other.

♦ Move the workpiece evenly backwards and

forwards in order to achieve optimal results. This

also ensures that the grinding disc is worn

down more evenly.

Changing the grinding disc/

buﬃng disc

WARNING! RISK OF INJURY!

►Always remove the power plug from the

wall socket before carrying out any work

on the appliance.

WARNING!

► The grinding or buﬃng disc used may

not be any larger than the prescribed diameter.

► Replace the grinding or buﬃng disc

when the outer diameter is less than 50mm.

NOTE

► Please note that you will require tools which

are not included in delivery for the assembly.

♦ Using a Torx-T10-screwdriver, unscrew the ﬁx-

ing bolts from the side protective covers

(seeﬁg. E). Remove the protective covers on

both sides.

♦ If you want to change the buﬃng disc , un-

screw the attachment for the ﬂexible shaft .

♦ Unscrew the union nut from the shaft

using a 17 mm wrench. Hold the aﬀected

grinding or buﬃng disc ﬁrmly in one

hand to create a suitable counterpressure.

♦ Remove the tension disc and grinding

or buﬃng disc .

♦ Place the new grinding or buﬃng disc on

the shaft .

♦ Push the tension disc back onto the shaft .

♦ Screw the union nut back onto the shaft .

♦ Re-tighten the union nut . Hold the grinding

or buﬃng disc that you have just attached

ﬁrmly in one hand to create a suitable counter-

pressure.

WARNING! RISK OF INJURY!

► Never use the grinding or buﬃng disc

without the protective cover .

CAUTION! PROPERTY DAMAGE!

► Do not tighten the union nut too tightly

since the grinding disc could otherwise

break.

♦ Reﬁt the protective cover and ﬁx it in place

by tightening the ﬁxing screws .

Fitting the ﬂexible shaft

WARNING! RISK OF INJURY!

►Always remove the power plug from the

wall socket before carrying out any work

on the appliance.

♦ Screw the ﬂexible shaft onto the connecting

thread of the appliance. To do this, push the

axle core of the ﬂexible shaft into the square

hole on the connecting thread . Turn the lock-

ing nut anticlockwise to tighten it.

WARNING! RISK OF INJURY!

► Make sure that the eye shields are folded

down to the tool rests . This can prevent

unintentional contact with the grinding or

buﬃng disc .

► After use, remove the ﬂexible shaft from

the appliance. Otherwise, the ﬂexible shaft

could start thrashing about in an uncontrolled

manner and cause an injury when you switch

the appliance on.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PDFW 120 A2 - IAN 353549 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside PDFW 120 A2 - IAN 353549

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info