Bedienungsanleitung Parkside PDFW 120 A2 - IAN 353549 (Seite 16 von 65) (Englisch)

762964

Zoom out

Zoom in

Vorherige Seite

1/65

Nächste Seite

PDFW 120 A2

■ 12 │ GB│IE│NI│CY

Adjusting the tool rests

♦ Adjust the workpiece rests with the aid of

the knurled screws . Ensure that the space

between the grinding or the buﬃng disc

and the tool rest is as low as possible.

Ensure that the workpiece rests do not come

into contact with the grinding or the buﬃng

discs .

♦ Adjust the distance repeatedly as the

grinding or buﬃng disc wears down.

Fitting the spark deﬂectors

♦ Fit the spark deﬂectors with the aid of the

ﬁxing bolts for the spark deﬂectors , nuts,

washers and spring washers to the top of the

device (see ﬁg. C).

♦ Tighten the nuts using a pair of pliers or a 7 mm

open end wrench. Tighten the ﬁxing bolts for

the spark deﬂector using a Phillips screw-

driver.

♦ Fit the spark deﬂectors so that the distance

between the grinding or buﬃng disc and

the spark deﬂector is as small as possible.

The gap should not be greater than 2 mm.

Ensure that the spark deﬂectors do not come

into contact with the grinding or the buﬃng

discs .

♦ Adjust the distance repeatedly as the

grinding or buﬃng disc wears down.

Fitting the eye shields

♦ Attach the eye shields to the ﬁxtures provided

on the spark deﬂectors using the mounting

screws for the eye shields , nuts, washers and

spring washers (see ﬁg. C).

♦ Tighten the nuts using a pair of pliers or a 8 mm

open end wrench. Tighten the ﬁxing bolts for

the eye shields using a Phillips screwdriver.

Working procedures

Ensure that the appliance is always stable

and secure. For extra safety, you can secure

the appliance in a suitable location. There are

4 drill holes in the housing foot that can

be used for attachment to a secure and level

surface. Feed a suitable ﬁxing material that

is appropriate for the surface (not supplied)

through the 4 drill holes . Fix the appliance

to the surface using the ﬁxing material.

Ensure that the grinding and buﬃng

discs are not blocked.

Ensure that the eye shields , spark deﬂec-

tors and tool rests are properly ﬁtted

and adjusted!

A light grinding pressure is suﬃcient

Work using a light grinding pressure – a constant

and correct speed will ensure the best grinding

performance.

Grinding

Bear in mind that the workpiece heats up during

grinding. Therefore, cool the workpiece in a water

bath. Dry it thoroughly before you resume working.

Operation

Switching on and oﬀ

■ Direction of rotation of the tool!

NOTE

► Before ﬁrst use, allow the grinding and

buﬃng discs to run without a load at top

speed for about 5 minutes. When doing so,

stay out of the hazard area in front of and

next to the openings in the grinding or the

buﬃng disc .

WARNING! RISK OF INJURY!

► Ensure the lowest-possible distance (gap)

between the grinding or the buﬃng

disc and the tool rest .

► If the appliance suddenly brakes completely

or jams, it must be switched oﬀ immediately.

♦ Set the eye shields so that they provide the

greatest possible protection.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PDFW 120 A2 - IAN 353549 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside PDFW 120 A2 - IAN 353549

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info