Bedienungsanleitung Parkside PDM 600 A1 - IAN 322988 (Seite 23 von 84) (Deutsch, Englisch, Holländisch, Französisch, Polnisch)

782072

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

18 GB/IE

2. At the end of the workpiece, produce an approx. 2mm

deep saw cut along the diagonal, in order to receive the

headstock drive centre (4).

3. Use a wood mallet (not supplied) to drive the headstock

drive centre (4) into the point where the diagonal cuts

across the end of the workpiece. Take care to protect the

threaded end of the headstock drive centre (4) so that no

object damages the thread.

4. Cut the corners oﬀ the workpiece if the diameter of the

ends is greater than 5 cm x 5 cm to make turning easier

and safer.

5. Measure the combined total length of the workpiece with

the headstock drive centre (4) and centering pin (7) on

each end.

6. Loosen the clamping lever for the tailstock (9) and set

the distance between the headstock drive centre (4) and

the centring pin (7), such that a slightly greater distance

is obtained than the measured total length of the work-

piece.

7. Tightly screw the headstock drive centre (4) with work-

piece onto the centering pin (7) by the hand wheel (10).

8. Once positioned fasten the counternut (8) against the tail

stock (9).

9. Set the tool support (5) with tool rest (6) approx. 3 mm

away from the workpiece.

Caution: Before starting the machine test the setup

by rotating the workpiece by hand to ensure that

there is enough clearance all the way around and

that it does not come into contact with the tool sup-

port (6).

Using the face plate: (Fig. 3)

To use the faceplate:

• The faceplate (15) oﬀers solid and secure support for a

variety of turned objects such as platters, bowls, pots and

round pieces.

Installing the faceplate:

1. Loosen the headstock drive centre (4) and remove from

the spindle.

2. Thread the faceplate (15) onto the headstock spindle

and tighten by hand and the wrench.

Securing workpiece on the faceplate:

Workpieces that cannot be worked using the headstock drive

centre (4), instead must be mounted on a faceplate (15) or a

backing piece, such as a chuck or block of wood.

1. Rough cut the workpiece as close as possible to the ﬁnal

shape before mounting onto the faceplate (15).

2. Firmly attach the faceplate (15) to the workpiece. De-

pending on the workpiece, this can be done with wood

screws (not supplied) driven directly into the workpiece.

Where the intended cutting dimensions do not allow for

screws, a backing piece might be required. A backing

piece can be made from a piece of scrap wood cube

with two ﬂat and parallel opposite faces. Identify and

mark the centre of the backing piece.

It may be necessary to bond the carrier part (wooden

block) with the workpiece and attach it to the carrier part,

before fastening it to the face plate (15) using screws (not

included in the scope of delivery). In this case, clamp the

backing piece to the workpiece and wait for the glue to

dry according to the glue manufacturer’s recommenda-

tion. Where the use of screws into the workpieceis not

permissible, the workpiece can be glued onto a backing

piece with a piece of paper placed in between the joint.

This allows for later separation without damage caused

to the workpiece. Use only non-tapered head wood

screws. Do not use tapered head wood screws.

Caution: Pay attention to the wood turning chisel

so that it does not interfere with the holding screws

at the ﬁnished dimensions of the workpiece.

Switching on and oﬀ (Fig. 1)

• Press the On switch (2/„I“)to start the machine.

• Press the Oﬀ switch (2/“0“) to stop the machine.

Caution: The device starts running immediately at

the set speed.

Speed adjustment (Fig. 1)

The correct speed must be set to suit the workpiece to be pro-

cessed.

Electronic speed control:

Use the electronic speed control to steplessly set the speed:

Set the speed with the help of the speed control (3).

Important information for operation

• We recommend that you refer to specialised literature on

wood-turning techniques.

• Look out for knots and shrinkage shakes when selecting the

wood for your turning work. Only use wood which is free

of cracks and large knots (where there are small knots, take

appropriate care with the pressure applied with the turning

tool).

• Always check that the shaped item is securely held by check-

ing it by hand. Warning! Pull out the power plug!

• Use only an original turning tool which is sharp.

• Do not stand in the ﬂight path of the workpiece when turning

wooden disks.

• Please cut large and imbalanced shaped items to size as

best as possible using a bandsaw or fretsaw. If the shaped

items are very imbalanced they will pose a risk to your health

and to the service life of the machine.

• Always start with the lowest possible speed for new work-

pieces being turned and increase it with increasing massive-

ness of the workpiece being turned.

• Do not use wooden disks with contraction cracks, since they

pose a high risk of bursting under the impact of centrifugal

forces.

• Do not exceed the maximum workpiece sizes.

• In case of tools which get blocked: Pull out the power plug

ﬁrst before starting troubleshooting.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PDM 600 A1 - IAN 322988 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info