782072
25
Zoom out
Zoom in
Vorherige Seite
1/84
Nächste Seite
20 GB/IE
Old devices must not be disposed of with household waste!
This symbol indicates that this product must not be disposed of together with domestic waste in compliance with the Directive (2012/19/
EU) pertaining to waste electrical and electronic equipment (WEEE). This product must be disposed of at a designated collection point.
This can occur, for example, by handing it in at an authorised collecting point for the recycling of waste electrical and electronic equip-
ment. Improper handling of waste equipment may have negative consequences for the environment and human health due to poten-
tially hazardous substances that are often contained in electrical and electronic equipment. By properly disposing of this product, you are also
contributing to the effective use of natural resources. You can obtain information on collection points for waste equipment from your municipal
administration, public waste disposal authority, an authorised body for the disposal of waste electrical and electronic equipment or your waste
disposal company.
16. Troubleshooting
Trouble Possible cause Solution
Quality of cut is poor. Cutting tool is dull. Sharpen or replace cutting tool.
Cutting too aggressive cut. Reduce the working pressure.
Cutting tool is positioned below workpiece
center line.
Lower cutting tool to maximum 3mm above the centre line of
workpiece.
Lathe speed too slow Increase lathe speed
Excessive vibration when
turning thin workpieces.
Cutting tool is positioned below workpiece
centre line.
Raise cutting tool to centerline of workpiece.
Cutting to aggressively. Use a lighter touch.
Excessive vibration when
turning large workpieces or
bowls.
Headstock and/or tailstock improperly
located at ends of workpiece.
Check for proper workpiece centres at headstock and/or
tailstock.
Workpiece is unbalanced. Trim end of workpiece until workpiece is more balanced.
Lathe will not turn on. Cord not connected into electrical outlet. Connect to electrical outlet.
Lathe will not turn off. Damaged or faulty power switch and/or
internal wiring.
Unplug the lathe from its electrical outlet immediately. Do not
operate lathe until it is repaired by a qualified service technician.
25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Parkside PDM 600 A1 - IAN 322988 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info