Bedienungsanleitung Parkside PDSS 310 A1 - IAN 96878 (Seite 40 von 45) (Deutsch, Englisch, Holländisch)

595413

Zoom out

Zoom in

Vorherige Seite

1/45

Nächste Seite

40 GB

After initial use / Maintenance / Cleaning and Care / Troubleshooting

Commissioning

First wrap a piece of Teﬂon tape (not included)

around the outer threads of the plug nipple

and the lubricator

(see ﬁg. B).

Now screw the plug nipple

into the thread

of the lubricator

(see Figure C).

Tighten this connection with moderate force

and absolutely using pliers.

Now turn the combination of lubricator

and

plug nipple

into the connection thread

of the impact driver (see Fig. C).

Also retighten this connection with pliers.

Now press the air hose onto the plug nipple

using a little force, until the hose locks in.

ATTENTION! Be sure the air hose

is ﬁrmly connected. A loose hose

whipping about out of control pre

sents

a major hazard. Also ensure the two screw

connections between lubricator

, coupling

and machine are securely seated.

Adjusting the compressed air

Note: this device is designed for an operating

pressure of up to 6.3 bar and a compressor with

the minimum air ﬂow speciﬁed in the technical spe-

ciﬁcations. When setting the air pressure, remember

the pressure drops by approx. 0.6 bar with a hose

length of 10 m and an inside diameter of 9 mm.

Only use ﬁltered, lubricated and regulated

compressed air.

Adjusting the torque

Set the torque control

to the correct torque

by pressing it toward the housing and turning it

until it locks at the desired setting.

Be sure the operating pressure of the compres-

sor is between 5 and 6.3 bar.

Note: the ideal pressure is 6.3 bar. The maximum

torque cannot be reached at a pressure of only 5

bar or with insuﬃcient air ﬂow.

Setting

1 (low, min.)

2 (normal)

3 (high)

4 (extra high,

max.)

Initial use

Activate the trigger

to start the equipment.

Release the trigger

to deactivate the equip-

ment.

Changing rotation

ATTENTION! The device must come to a

complete standstill before changing the direc-

tion of rotation.

ATTENTION! A machine rotating in an unex-

pected direction can be dangerous. Always

pay attention and use care.

Note: The impact driver clockwise / counter-

clockwise rotation. Use the reverse switch

to change the direction of the impact driver.

Pull the bolt forward in the direction of the „F“

marking („Forward / Fasten“) for clockwise

operation. You can now e.g. tighten screws.

Push the bolt back towards the „R“ marking

(„Reverse / Release“) so it protrudes from the

back of the equipment to set to counter-clock-

wise mode. You can now e.g. loosen screws.

Correctly holding the

equipment

This equipment weighs 2.3 kg.

Hold the equipment with both hands to ensure

safe operation (see Fig. D and E).

96878_par_Druckluft-Schlagschrauber PDSS 310 A1_content_DE_AT_NL.indd 40 23.04.14 15:55

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside PDSS 310 A1 - IAN 96878 Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside PDSS 310 A1 - IAN 96878

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info