Bedienungsanleitung PerfectPro Workstation (Seite 6 von 36) (Deutsch, Englisch, Holländisch, Französisch)

742531

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

9 10

Finding new stations – DAB

Fromtimetotime,newstationsmaybecomeavailable.Youmayproceedtondnew

stations as follows:

1. In DAB mode, press the Menu button, “Full scan” shows on the display.

2. Press the Tuning knob, the radio will perform a scan of the Band III DAB

channels. As new stations are found, the station counter on the right-hand side of

the display will increase and new radio stations found will be added to the list stored

in the radio.

Manual Tuning – DAB

Manualtuningisanalternativemethodofndingnewstations.Insteadofscanningthe

entire Band III channels automatically, you may tune the radio directly to a known DAB

channel and store all the multiplex in that channel into the available station list.

1. In DAB mode, press the Menu button and rotate the Tuning knob until the LCD

display shows “Manual Tune”, then press the Tuning knob. The display will show

DAB channel and Frequency.

2. Rotate the Tuning knob to select the desired channel or Frequency and press the

Tuning knob to tune to the chosen frequency.

3. When DAB stations in the tuned channel are found, the display will show the

name of the station. Any new radio stations found will be added to the list stored in

the radio.

4. Thesignalstrengthdisplayshowsthereceptionofthestation.Theclearunlled

rectangle indicates minimum signal level required for satisfactory reception. The

signal strength bars will go up or down showing the changing signal strength as you

adjust the antenna or the position of the radio.

5. Repeat step 1 to 4 for other channels with new stations.

6. Press the Menu button twice to exit manual tuning and return to normal

DAB operation.

Dynamic Range Control (DRC) settings – DAB

DRC can make quieter sounds easier to hear when your radio is used in a noisy

environment.

1. In DAB mode, press the Menu button and rotate the Tuning knob until “DRC

value” appears on the display, press the Tuning knob.

2. Rotate the Tuning knob to select required DRC setting (default is OFF).

DRC off DRC is switched off, broadcast DRC will be ignored.

DRC high DRC is set as sent by broadcaster.

DRC low DRC level is set to 1/2 that sent by broadcaster.

3. Press the Tuning the knobtoconrmthesetting.Thedisplaywillreturntonormal

radio display.

Note: Not all DAB broadcasts are able to use the DRC function. If the broadcast does

not support DRC, then the DRC setting in the radio will have no effect.

FM MODE

Operating the radio – FM seek station

1. Press the On/Off button to turn on the radio.

2. Select the FM waveband by pressing the Source button.

3. IfthisisthersttimetoswitchtoFMmode,thestationinpreset1willbeplayed.If

the radio has been used before, the last listened station will be played.

4. To seek station, press the Tuning knob.Thescanstopsautomaticallywhenitnds

 astationofsufcientstrength.

5. After a few seconds, the display will update and show station name if RDS

information is being received.

6. Tondthenextstation,presstheTuning knob again.

7. To seek stations in an opposite direction, rotate the Tuning knob clockwise (to scan

from low frequency to high frequency) or rotate counter clockwise (to scan from

high frequency to low frequency), and press the Tuning knob.

8. When the waveband end is reached, the radio will recommence tuning from the

opposite waveband end.

Manual tuning – FM

1. Press the On/Off button to turn on the radio.

2. Select the FM band by pressing the Source button.

3. Rotate the Tuning knob to reach the preferred FM station. The radio will change

the frequency in steps of 50 kHz.

4. Rotate the rubber antenna to get the best reception. If the radio is tuned to a

 stationofsufcientsignalstrengthwithRDSinformationpresent,thedisplaymay

change to show the station name. 5. When the waveband end is reached, the radio

will recommence tuning from the opposite waveband end.

RDS station service – FM

RDS (Radio Data System) is an information system which inaudible digital information

is transmitted in addition to the normal FM radio program. When the radio is receiving a

RDSstationandthereceptionstrengthissufcient,thestationnamewillappearinthe

display. It may take some time before the RDS information is available.

Calling up RDS information

When you are listening to a FM station with RDS system, repeatedly press the Info

button to cycle through the information. This will only function if the reception level is

sufcientandclear.

a. Radio text (RT) Displays the message about the station being listened to as

ticker text.

b. Program type (PTY) Displays the type of station being listened to, e.g. Pop, Classic,

News, etc.

c. Frequency Displays the frequency of the station being listened to.

d. Stereo or Mono Displays Stereo or Mono.

e. Signal level Displays the signal strength.

f. Time & date Displays the current time (24 hour clock) and date.

PerfectPro Workstation Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info