Bedienungsanleitung Philips cc 5060 17 (Seite 2 von 9) (Deutsch, Englisch, Holländisch, Französisch)

401659

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

ENGLISH

Introduction

Congratulations on your purchase and welcome to

Philips! To fully benet from the support that Philips offers,

Your new Philips kids’ clipper works very quietly and

offers excellent performance. It is easy to use and easily

follows the contours of your child’s head.

We have included a separate instruction DVD that gives

you tips and instructions on how to cut your child’s hair

and how to create different hairstyles with this clipper.

General description (Fig. 1)

A Large comb

B Cleaning brush

C Styling comb

D Scissors

E Cape

F Pouch

G Adapter

H Appliance plug

I Battery light

J On/off button

K Cutting unit

L Setting selector

M Small comb

N Appliance socket with dust protection plug

Important

Read this user manual carefully before you use the

appliance and save it for future reference.

Danger

Make sure the adapter does not get wet.

This appliance is NOT a toy but an electric hair

clipper. If the appliance is used on young children’s

hair, it must be operated by a responsible adult. Keep

the appliance out of the reach of young children.

Warning

The adapter contains a transformer. Do not cut off

the adapter to replace it with another plug, as this

causes a hazardous situation.

This appliance is not intended for use by persons

(including children) with reduced physical, sensory

or mental capabilities, or lack of experience and

knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a

person responsible for their safety.

Children should be supervised to ensure that they

do not play with the appliance.

Caution

Use, charge and store the appliance at a temperature

between 15°C and 35°C.

Do not charge the appliance in a pouch or cassette.

Only use the adapter supplied.

If the adapter is damaged, always have it replaced

with one of the original type in order to avoid a

hazard.

Do not use the appliance if the cutting unit or the

combs are damaged or broken, as this may cause

injury.

This appliance is only intended for clipping human

scalp hair. Do not use it for another purpose.

Do not use the appliance in the bath or in the

shower.

Never immerse the appliance in water or any other

liquid, nor rinse it under the tap.

General

The adapter transforms 100-240 volts to a safe low

voltage of less than 24 volts.

Electromagnetic elds (EMF)

This Philips appliance complies with all standards

regarding electromagnetic elds (EMF). If handled

properly and according to the instructions in this user

manual, the appliance is safe to use based on scientic

evidence available today.

Preparing for use

Charge indications

Charging

When you charge the appliance, the battery light ashes

green to indicate that the appliance is charging.

Battery fully charged

When the battery is fully charged, the battery light lights

up green continuously.

Battery running low

When the battery is running low, the battery light turns

orange.

Note: When the battery light turns orange, the battery still

contains enough power for one haircut (approx. 15 minutes).

Recharge the appliance as soon as the motor starts to run

more slowly.

Charging the appliance

Charge the appliance for at least 8 hours before you use

it for the rst time and after a long period of disuse or

when the battery light turns orange to indicate that the

battery is almost empty.

When it is fully charged, the appliance has a cordless

operating time of up to 45 minutes.

1 Switch off the appliance.

2 Insert the appliance plug into the appliance and put

the adapter in the wall socket (Fig. 2).

After a few seconds, the battery light starts ashing

green to indicate that the appliance is

charging (Fig. 3).

When the battery is fully charged, the battery light

lights up green continuously.

3 Remove the adapter from the wall socket when the

battery is fully charged (after 8 hours).

Corded clipping

When the rechargeable battery is empty, you can also run

the appliance from the mains.

Using the appliance

Clipping with comb

Note: Make sure the hair is clean and dry. Do not use the

appliance on freshly washed hair.

Note: Make sure the head of the person whose hair you

are cutting is at the same level as your chest. This ensures

that all parts of the head are clearly visible and within easy

reach.

1 Comb the hair with the styling comb in the

direction of hair growth.

2 Choose whether you want to use the large or small

comb, depending on the desired hair length.

Use the small comb for a hair length of 3-21mm and use

the large comb for a hair length of 24-42mm.

3 Slide the comb into the guiding grooves of the

appliance (‘click’) (Fig. 4).

Make sure that the arms of the comb have been slid

properly into the grooves on both sides.

4 Press the setting selector (1) and slide the comb

to the desired hair length setting (2). Then release

the setting selector to lock the hair length

setting (Fig. 5).

Hair length settings

The settings are shown on the arms of the comb.

The settings correspond to the remaining hair length

after cutting (Fig. 6).

The small comb cuts the hair to a length of 3mm,

6mm, 9mm, 12mm, 15mm, 18mm or 21mm.

The large comb cuts the hair to a length of 24mm,

27mm, 30mm, 33mm, 36mm, 39mm or 42mm.

5 Switch on the appliance (Fig. 7).

6 Move the appliance through the hair slowly.

Note: Make sure that the at part of the comb is fully in

contact with the scalp to obtain an even cutting result.

Tips:

Start clipping at the highest hair length setting of the

comb and reduce the hair length setting gradually.

Write down the hair length settings you use to

create a certain hairstyle as a reminder for future

clipping sessions.

To clip most effectively, move the appliance against

the hair growth direction.

Try different directions (upward, downward or

across), because hair doesn’t all grow in the same

direction.

Make overlapping passes over the head to ensure

that the appliance catches all the hairs that need to

be cut.

Make sure that the at part of the comb is fully in

contact with the scalp to obtain an even cutting

result.

To achieve a good result with curly, sparse or long

hair, you can use the styling comb to guide the hair

towards the appliance.

Regularly remove cut hair from the comb. If a lot of

hair has accumulated in the comb, remove it from the

appliance and blow and/or shake the hair out of it.

Clipping without comb

You can use the clipper without comb to contour the

neckline and the area around the ears.

The comb keeps the cutting unit at a certain distance

from the head. This means that, if you use the clipper

without the comb, the hair is cut off very close to the skin.

1 Press and hold the setting selector (1) with one

hand and pull the comb off the appliance (2) with

your other hand (Fig. 8).

Never pull at the exible top of the comb. Always pull at

the bottom part.

2 Before you start to contour the hairline round the

ears, comb the hair ends over the ears.

3 Tilt the appliance in such a way that only one edge

of the cutting element touches the hair ends.

4 Only cut the hair ends. The hairline has to be close

to the ear.

5 To contour the neckline and sideburns, turn the

appliance and make downward strokes.

6 Move the appliance slowly and smoothly. Follow the

natural hairline.

Graduation

The Philips hair clipper not only allows you to cut the hair

evenly at the same length all over the head, it also enables

you to achieve a smooth transition from longer hair on

top of the head to shorter hair on the back and sides of

the head.

1 Slide the large comb into the guiding grooves of the

appliance (‘click’) (Fig. 4).

2 Start clipping at the setting for maximum hair

length (42mm).

3 Then choose a shorter setting and cut the hair on

all parts of the head, except for the top, where you

want the hair to be longer.

4 Repeat this procedure until all hairs have the

desired length.

Cutting over styling comb or ngers

This technique can be used to obtain hair lengths over

42mm. Bear in mind that this technique is difcult to

master and should only be applied by experienced users.

1 Press and hold the setting selector (1) with one

hand and pull the comb off the appliance (2) with

your other hand (Fig. 8).

Never pull at the exible top of the comb. Always pull at

the bottom part.

2 Comb a small section of hair upwards.

3 Lift the hair with the styling comb and hold it

between your ngers until only the length that

needs to be cut sticks out.

4 Cut the hair protruding from the comb or ngers.

5 Continue this procedure and comb frequently to

remove cut hair and to check for unevenly cut

sections.

Cleaning

Clean the appliance every time you have used it.

Never use scouring pads, abrasive cleaning agents or

aggressive liquids such as alcohol, petrol or acetone to

clean the appliance.

Only clean the appliance with the cleaning brush

supplied.

Note: The appliance does not need to be lubricated.

1 Make sure the appliance is switched off and

disconnected from the mains.

4222.002.8043.1

2/9

Philips cc 5060 17 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info