Bedienungsanleitung Philips DVDR80 (Seite 114 von 120) (Englisch)

1055

114

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

104

OBefore you call an engineer

If you have any problems using this DVD recorder, the reason may be one of the following. You

can also call the customer service centre in your country.

The telephone numbers can be found on the back of this instruction manual.

You can also visit our web page 'http://www.p4c.philips.com' .

Have the model number (MODEL NO) and the production number (PROD.NO) of your

recorder ready.

The production number (PROD. NO.) is printed on the type plate at the back.

PROBLEM SOLUTION

Your recorder does

not respond to any

button being pressed

and the display shows

'IS TV ON?':

bRecorder in initial installation mode: Switch on the TV, switch over to the DVD recorder socket.

Now the menu for language selection should appear. Please read paragraph 'Initial Installation' in

the chapter 'Installing your DVD Recorder'.

The following text should now appear on the screen ''. Please read paragraph 'Initial Installation' in

the chapter 'Installing your DVD Recorder'.

The device does not

react when you press a

button, although the

remote control works:

b'Dealer-Mode' is switched on: All buttons on the front of the set are locked.

Switch off the function:

1 Pull out the mains plug from the wall outlet.

2 Press and hold down h and OPEN/CLOSE J and put back the mains plug into the wall

outlet.

3 As soon as the time or '--:--' appears in the display (ca. 6 - 10 seconds), release h and

OPEN/CLOSE J .

Your DVD recorder

does not respond to

any button being

pressed:

bThere is no power supply: check the power supply

bA programmed recording (Timer) is currently being made: If desired, cancel the programmed

recording (Timer) with STANDBY m .

bThere is a technical problem: disconnect from the mains power supply for 30 seconds, then

connect again.

If this doesn't help, you can reset your DVD recorder to the default factory settings.

Resetting the machine

to the default factory

settings

bImportant:

All the information stored (TV channels, time and date, TIMER) will be lost.

1 Disconnect from the mains power supply.

2 Press and hold down the STANDBY-ON m button on the device and reconnect to the

mains power supply.

3 Release the STANDBY-ON m button when 'IS TV ON?' appears on the display. All the

information stored (TV channels, time and date, TIMER) will be lost.

Please read paragraph 'Initial Installation' in the chapter 'Installing your DVD Recorder'.

Remote control does

not work:

bRemote control not pointed toward the DVD recorder: Point the remote control at the machine.

See if the 'o(((' appears on the display briefly each time you press a remote control button. If it

does, the Recorder is receiving information from the remote correctly.

bThere is a technical problem: Take out the batteries, wait for 10 seconds and put them in again.

bBatteries are flat: Change the batteries.

Before you call an engineer

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips DVDR80 Seite 114

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Philips DVDR80

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info