Bedienungsanleitung Philips FT565 (Seite 5 von 44) (Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

799038

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

transmitters. In the case of very powerful

medium wave transmitters the indicator may

light up on several consecutive tuning frequen-

cies.

(u) 'STEREO' indicator

This lights up if the tuned transmitter is received

in stereo.

@ 'MEMORY' button

Button for starting the programming procedure.

If this button is pressed, then it is possible to

programme the pre-selected transmitter for

5 seconde. During the programming procedure

the tuner is in memory mode, indicated by the

lighting up of the word 'MEMORY' on display (f).

@ 'LW' selector button

For selecting the long wave tuning range.

When this button is pressed, the 'LW' indicator

lights up on display ®.

@ 'MW' selector button

For selecting the medium wave tuning range.

When this button is pressed, the 'MW' indicator

lights up on display @.

@ 'FM' selector button

For selecting the 'FM' tuning range.

When this button is pressed, the 'FM' indicator

lights up on display @.

OPERATION

The tuner may be operated directly or via remote

control.

In both cases the amplifier must first be switched

on.

Operating via remote control

This is only possible with preprogrammed stations.

Programming can not be done with the aid of the

remote control, but only directly from the tuner.

You should therefore first programme the tuner and

then read the instructions for operating the tuner in

the booklet supplied with the remote control.

With the amplifier switched on and set to tuner

playback (the 'TUNER' indicator is lit up!) the

transmitters can be tuned as follows:

1. Switch the tuner on by pressing 'ON/OFF'

switch 0. The tuner then returns automatically

to the last position it was in before it was

switched off.

2. Select LW, MW or FM by pressing 'LW' button

@, 'MW' @ or 'FM' @.

In the 'LW' position indicators 'LW' and 'kHz'

light up on display (s).

In the 'MW' position indicators 'MW' and 'kHz'

light up on display (s).

In the 'FM' position indicators 'FM' and 'MHz'

light up on display ®.

3. Three different ways can then be used con-

secutively to tune to the required transmitter,

i.e. automatic tuning, manual tuning and tuning

on pre-selected transmitters.

A. Automatic tuning

• By pressing button ® 'DOWN' or @ 'UP' once

andforlongerthan 0.5 second, the selected tuning

range is searched step by step until the tuner

locates a transmitter of adequate strength, at which

it stops. Indicator @ 'TUNED' lights up. If it is a

stereo transmission, indicator @ 'STEREO' lights

up.

• If the station selected is not the one you want,

press button ® or @ again. Automatic tuning is

then resumed, until another station is located.

Wofe; If the end of a tuning range is reached, tuning

stops and begins again from the other end of the

tuning range.

• Depress, if desired, key @ 'FM-NR' to reduce

possible noise.

• During tuning the audio signals are completely

suppressed, in order to prevent any interference

from parasitic noise.

Note:

Relatively weak transmitters are passed over

during automatic tuning and can only be selected

with manual tuning.

Tuner does not search

- The frequency has only changed by one step and

you have not pressed button @ or (D for long

enough.

The tuner locates few stations

- The aerial signals received are too weak.

- Check the aerial connections.

- Adjust the position of the AM frame or the FM

indoor aerial.

If this does not give satisfactory results, the

transmitters received are too weak,

In this case consider connection to external

aerials or cable network.

- If these are already fitted, check their connection

to the tuner.

B. IVIanual tuning

• To help prevent poorly tuned transmitters being

stored in the memory, it is useful to know the exact

tuning frequency of the transmitters received in the

area.

For this Information consult a programme

magazine.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Philips FT565 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info