Bedienungsanleitung Pioneer ND-BC2 (Seite 6 von 8) (Englisch, Französisch)

811499

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

Fig. 16

Abb. 16

Fig. 17

Abb. 17

① Pull out from here ② Hinge

③ Harness cover

⑤ Hatch

④ Rear view

camera

① Rear view camera

② Hatch

③ Cord

② Waterproof pad

Fig. 18

Abb. 18

① Clamps

③ Rubber packing

④ Make a U-shaped loop in

the lead outside the rubber

packing to prevent rain-

water from flowing along

the lead into the interior

of the vehicle.

Connection <ENGLISH>

Note:

• This unit is for vehicles with a 12-volt battery and nega-

tive grounding. Before installing it in a recreational vehi-

cle, truck, or bus, check the battery voltage.

• To avoid shorts in the electrical system, be sure to discon-

nect the battery cable before beginning installation.

• Refer to the owner’s manual for details on connecting the

other units, then make connections correctly.

• Secure the wiring with cable clamps or adhesive tape. To

protect the wiring, wrap adhesive tape around them where

they lie against metal parts.

• Route and secure all wiring so it cannot touch any mov-

ing parts, such as the gear shift, handbrake and seat rails.

Do not route wiring in places that get hot, such as near

the heater outlet. If the insulation of the wiring melts or

gets torn, there is a danger of the wiring short-circuiting

to the vehicle body.

• Do not shorten any leads.

• Never feed power to other equipment by cutting the insu-

lation of the power supply lead of the unit and tapping

into the lead. The current capacity of the lead will be

exceeded, causing over heating.

• When replacing the fuse, be sure to only use a fuse of the

rating prescribed on the fuse holder.

• To minimize noise locate the TV antenna cable, radio

antenna cable and RCA power supply cable as far away

from each other as possible.

• Connection to a TV with an RCA video input is possible,

but confirm whether the TV you use has a reverse gear

connection function.

• If this unit is installed in a vehicle that does not have an

ACC (accessory) position on the ignition switch, the red

lead of the unit should be connected to a terminal coupled

with ignition switch ON/OFF operations. If this is not

done, the vehicle battery may be drained when you are

away from the vehicle for several hours.

ACC position No ACC position

• Cords for this product and those for other products may

be different colors even if they have the same function.

When connecting this product to another product, refer to

the supplied manuals of both products and connect cords

that have the same function.

Connection sample (Fig. 14)

① Power supply unit

② Rear view camera connector

③ RCA power supply cable connector

④ Rear view camera

Video input jack

Connect to video input jack.

⑤ RCA pin

Accessory power supply

To electric terminal controlled by ignition

switch (12 V DC) ON/OFF.

⑥ Red

⑦ Fuse (1A)

Ground

To vehicle (metal) body.

⑧ Black

Cord installation (Fig. 15)

① Clamps

② Rear view camera

③ RCA power supply cable

④ Product with a video input jack

(Hideaway unit etc.)

⑤ Power supply unit

⑥ Made with a rasp etc.

⑦ Scuff plate

⑧ Clamp

⑨ Waterproof plate

Cord installation points (Fig. 16)

• When pulling the cord out of the car,

pull from the outer side of the hatch har-

ness cover and hinge.

① Pull out from here

② Hinge

③ Harness cover

④ Rear view camera

⑤ Hatch

After cord installation (Fig. 17, Fig. 18)

• Open and close the hatch door slowly

to confirm that the cord is not rubbing

against the rim of the door.

① Rear view camera

② Hatch

③ Cord

• When the rear view camera cord cannot

be pulled out from the lower side due to

the type of car.

As shown in the figure 18, bend the cord

into a U shape in front of the waterproof

pad, making sure that rain water cannot

enter the car by running down the cord.

① Clamps

② Waterproof pad

③ Rubber packing

④ Make a U-shaped loop in the lead outside

the rubber packing to prevent rainwater from

flowing along the lead into the interior of the

vehicle.

Power source ........................................... 14.4 V DC

(10.8 V to 15.1 V allowable)

Grounding system .............................. Negative type

Max. current consumption .......................... 120 mA

Output video ....................................... Mirror image

(for rear view confirmation)

Sensor ............................ 1/4-inch color CCD sensor

No. of pixels ........ 492 (vertical) × 512 (horizontal)

(Total no. of pixels: 270 000,

effective no. of pixels roughly 250 000)

Lens ........................................................ Wide-angle,

focal length f = 1.53 mm, F value 2.8

Angle of view ................... Horizontal: approx. 135º

Vertical: approx. 100º

IR cutoff filter (special filter for vehicle mounting)

.................................................................. Provided

Iris system .......................................... Electronic iris

Scanning system ........................................ Interlace

Synchronizing system ....... Internal synchronization

Signal-to-noise ratio .......................... 40 dB or more

(at the recommended intensity of illumination)

Horizontal resolution ............ Approx. 300 TV lines

Illumination range .... Approx. 1.5 lux to 100 000 lux

Image output ...................................... 1 Vp-p (75 Ω)

Operation temperature range ........... –30ºC to +70ºC

+22ºF to +158ºF

Storage temperature range .............. –40ºC to +85ºC

–40ºF to +185ºF

Dimensions

Camera unit ... 27 (W) × 27 (H) × 26 (D) mm

1 (W) × 1 (H) × 1 (D) in.

Power supply unit

.................... 70 (W) × 23 (H) × 35 (D) mm

2-3/4 (W) × 7/8 (H) × 1-3/8 (D) in.

Weight

Camera unit ................................ 150 g (0.3 lbs)

(including the cable)

Power supply unit ...................... 160 g (0.4 lbs)

(including the power cord)

Note:

Specifications and the design are subject to possible

modification without prior notice due to improve-

ments.

Specifications <ENGLISH>

Pioneer ND-BC2 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info