Bedienungsanleitung Pioneer SC-LX78-S (Seite 84 von 141) (Englisch)

580827

Zoom out

Zoom in

Vorherige Seite

1/141

Nächste Seite

Using other functions

About the Speaker B Link function

When 7.2ch + Speaker B or 5.2ch + SP-B Bi-Amp is selected for the Speaker System setting (page 103 ) and

Speaker B Link (HDMI Setup on page 75 ) is set to “ON”, the setting of the speaker terminals that are played

changes automatically when HDMI OUT 1 and HDMI OUT 2 are switched. The setting switches as follows.

! OUT 1+2 – Switches to SP: A+B ON. Sound is output simultaneously in the room where the A speakers are

located and in the room where the B speakers are located.

! OUT 1 – Switches to SP: A ON. Sound is only output in the room where the A speakers are located.

! OUT 2 – Switches to SP: B ON. Sound is only output in the room where the B speakers are located.

HDMI 4K/60p signal output setting

If the TV to be connected using HDMI supports 4K/60p, you can switch the 4K/60p signal output setting in accor-

dance with TV performance.

Operation is performed on the front panel of the unit. You cannot perform the setting if the multizone function is

not set to MULTI ZONE OFF (page 84 ).

1 Switch the receiver into standby.

2 While holding down ENTER on the front panel, press u STANDBY/ON.

The display shows RESET c NO d.

3 Use i/j to select ‘4K/60p’.

4 Use k/l to select the signal to set.

! 4:4:4 – Select this setting when connecting to a 4K/60p 4:4:4 24 bit compatible TV using HDMI. More high

quality video images can be enjoyed.

— When the HDMI cable does not support 4K/60p 4:4:4 24 bit (18 Gbps transmission), video image may not

be output properly. In that case, select 4:2:0 to watch a 4K/60p 4:2:0 24 bit video image.

— The HDMI OUT 3 terminal does not output a 4K/60p 4:4:4 24 bit video image if MAIN/HDZONE is set to

HDZONE.

! 4:2:0 – Select this setting when connecting to a 4K/60p 4:2:0 24 bit compatible TV using HDMI.

5 When you’re finished, press RETURN.

6 Press u STANDBY/ON to switch on the receiver and your TV.

Make sure that the TV’s video input is set to this receiver.

Changing the channel level while listening

Using the channel level settings, you can adjust the overall balance of your speaker system, an important factor

when setting up a home theater system.

1 Press CH LV..

2 Use i/j to select the channel you wish to adjust.

3 Adjust the volume using k/l.

The volume can be adjusted in the range of -12.0dB to +12.0dB, 0.5 dB steps.

4 When you’re finished, press RETURN.

Input Volume Absorber

This can be used to correct for the difference in volume between input sources.

1 Switch to the input whose volume you want to adjust.

2 Press CH LV..

3 Use i/j to select ‘ALL’.

4 Adjust the volume using k/l.

The volume can be adjusted in the range of -12.0dB to +12.0dB, 0.5 dB steps.

5 When you’re finished, press RETURN.

Using the MULTI-ZONE controls

The following steps use the front panel controls to adjust the sub zone volume and select sources. See ZONE 2

remote controls and HDZONE remote controls on page 85 .

Important

! The settings must be changed at ZONE Setup in order to use the multi-zone function (page 109 ).

1 Press the button on the front panel for the zone you want to operate (ZONE 2 ON/OFF,

ZONE 3 ON/OFF or HDZONE ON/OFF).

The zone switches between on and off each time the button is pressed.

The MULTI-ZONE indicator lights when the MULTI-ZONE control has been switched ON.

2 Press MULTI-ZONE CONTROL on the front panel to select the sub zone(s) you want.

! When the receiver is on, make sure that any operations for the sub zone are done while ZONE and your

selected sub zone(s) show in the display. If this is not showing, the front panel controls affect the main zone

only.

If the receiver is in standby, the display is dimmed, and ZONE and your selected sub zone(s) continue to show

in the display.

3 Use the INPUT SELECTOR dial to select the source for the zone you have selected.

For example, ZONE 2 SAT/CBL sends the source connected to the SAT/CBL inputs to the primary (ZONE 2) sub

room.

! If you select TUNER, you can use the tuner controls to select a preset station (see Saving station presets on

page 60 if you’re unsure how to do this). The tuner cannot be tuned to more than one station at a time.

Therefore, changing the station in one zone also changes the station in the other zone. Please be careful not

to change stations when recording a radio broadcast.

4 Use the MASTER VOLUME dial to adjust the volume for the sub zone.

When Speaker System is set to anything other than 5.2 +ZONE 2+ZONE 3, 5.2 +ZONE 2+HDZONE or

Multi-ZONE Music, the volume output from the receiver’s AUDIO ZONE 2 OUT terminals can be fixed to –40 dB

or 0 dB and the volume can be adjusted from the connected amplifier. If you want to adjust the volume from the

connected amplifier, see ZONE Setup on page 109 .

5 When you’re finished, press MULTI-ZONE CONTROL again to return to the main zone

controls.

You can also press ZONE 2 ON/OFF, ZONE 3 ON/OFF or HDZONE ON/OFF on the front panel to switch off all

output to the sub zone.

! You won’t be able to switch the main zone off completely unless you’ve switched off the MULTI-ZONE control

first.

! If you don’t plan to use the MULTI-ZONE feature for a while, turn off the power in both the sub and main

rooms so that this receiver is in standby.

Note

When HDZONE is turned on, the video converter function is disabled. For that reason, video connected with the

video cable or component cable is not output from the HDMI terminal. Also, upscaling of the HDMI input video

cannot be performed. To enable the video converter function, turn off HDZONE.

Pioneer SC-LX78-S Seite 84

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer SC-LX78-S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info