Bedienungsanleitung Pioneer SC-LX78-S (Seite 85 von 141) (Englisch)

580827

Zoom out

Zoom in

Vorherige Seite

1/141

Nächste Seite

Using other functions

ZONE 2 remote controls

Before operation, hold down Z2 on the remote control (for 1.5 seconds) until the remote control LED flashes one time.

The following table shows the possible ZONE 2 remote controls:

Button(s) What it does

Switches on/off power in the sub zone.

ALL

Use to select the input function in the sub zone.

Input function buttons

Use to select the input function directly (this may not work for some functions) in the sub

zone.

VOLUME +/–

<a>

Use to set the listening volume in the sub zone.

MUTE

<a>

Mutes the sound or restores the sound if it has been muted (adjusting the volume also

restores the sound).

a ! The volume cannot be adjusted on the receiver if Volume Level at ZONE 2 Setup under ZONE Setup is set to –40 dB Fixed

or 0 dB Fixed.

ZONE 3 remote controls

Before operation, hold down Z3 on the remote control (for 1.5 seconds) until the remote control LED flashes one time.

The following table shows the possible ZONE 3 remote controls:

Button(s) What it does

Switches on/off power in the sub zone.

ALL

Use to select the input function in the sub zone.

Input function buttons

Use to select the input function directly (this may not work for some functions) in the sub

zone.

VOLUME +/–

<a>

Use to set the listening volume in the sub zone.

MUTE

<a>

Mutes the sound or restores the sound if it has been muted (adjusting the volume also

restores the sound).

a ! The volume cannot be adjusted on the receiver if Volume Level at ZONE 3 Setup under ZONE Setup is set to –40 dB Fixed

or 0 dB Fixed.

HDZONE remote controls

Before operation, hold down HDZ on the remote control (for 1.5 seconds) until the remote control LED flashes

one time.

The following table shows the possible HDZONE remote controls:

Button(s) What it does

Switches on/off power in the HDZONE.

ALL

Use to select the input function in the HDZONE.

Input function buttons

Use to select the input function directly (this may not work for some functions) in the

HDZONE.

VOLUME +/–

<a>

Use to set the listening volume in the HDZONE.

MUTE

<a>

Mutes the sound or restores the sound if it has been muted (adjusting the volume also

restores the sound).

a You can operate this only when Speaker System is set to 7.2ch + HDZONE, 5.2 Bi-Amp+HDZONE or 5.2 +ZONE 2+HDZONE.

Making an audio or a video recording

You can make an audio or a video recording from the built-in tuner, or from an audio or video source connected to

the receiver (such as a CD player or TV).

Keep in mind you can’t make a digital recording from an analog source or vice-versa, so make sure the compo-

nents you are recording to/from are hooked up in the same way (see Connecting your equipment on page 19

for more on connections).

! The receiver’s volume, Audio parameters (the tone controls, for example), and surround effects have no effect

on the recorded signal.

! Some digital sources are copy-protected, and can only be recorded in analog.

! Some video sources are copy-protected. These cannot be recorded.

Since the video converter is not available when making recordings (from the video OUT jacks) make sure to use

the same type of video cable for connecting your recorder as you used to connect your video source (the one you

want to record) to this receiver. For example, you must connect your recorder using Component video if your

source has also been connected using Component video.

1 Select the source you want to record.

You can use the input function buttons on the remote control or the front panel INPUT SELECTOR dial.

2 Prepare the source you want to record.

Tune to the radio station, load the CD, video, DVD etc.

3 Select the input signal according to the signal to be recorded.

Use the remote control’s AUDIO P. button.

4 Prepare the recorder.

Insert a blank tape, MD, video etc. into the recording device and set the recording levels. Refer to the instructions

that came with the recorder if you are unsure how to do this. Most video recorders set the audio recording level

automatically-check the component’s instruction manual if you’re unsure.

5 Start recording, then start playback of the source component.

Network settings from a web browser

Network settings can be made using the browser on a computer connected to the same LAN as the receiver.

1 Press u STANDBY/ON to switch on the receiver.

2 Turn on the computer’s power and launch the Internet browser.

3 Input the receiver’s IP address into the browser’s address input field.

Access the IP address“http://(the receiver’s IP address)” from a web browser. You can display the IP address of

the unit on the unit’s display by pressing the STATUS button on the remote control.

When connected with the receiver, the AVNavigator menu screen appears in the browser.

4 On the AVNavigator menu screen, select Network Setup.

5 Select the item you want to set.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer SC-LX78-S Seite 85

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer SC-LX78-S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info