Bedienungsanleitung Pioneer VSX-1019AH-K (Seite 104 von 128) (Englisch)

455217

104

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

Additional information12

104

No sound from surround

back speakers.

(Continued)

• If the source does not have 6.1 playback channels, make sure that surround

back channel processing is set to SBch ON and a surround mode is selected

(see Listening in surround sound on page 53).

• Check the speaker connections (see Connecting the speakers on page 18).

If only one surround back speaker is connected, make sure it’s connected to

the left channel speaker terminal.

No sound from subwoofer. • Check that the subwoofer is connected properly, switched on and the volume

turned up.

• If your subwoofer has a sleep function, make sure it is switched off.

• Make sure that the Subwoofer setting is YES or PLUS (see Speaker Setting on

page 95).

• The crossover frequency may be set too low; try setting it higher to match the

characteristics of your other speakers (see Speaker Setting on page 95).

• If there is very little low frequency information in the source material, change

your speaker settings to Front: SMALL / Subwoofer: YES, or Front: LARGE /

Subwoofer: PLUS (see Speaker Setting on page 95).

• Check that the LFE channel is not set to OFF, or a very quiet setting (see

Setting the Audio options on page 64).

• Check the speaker level settings (see Channel Level on page 96).

No sound from one speaker. • Check the speaker connection (see Connecting the speakers on page 18).

• Check the speaker level settings (see Channel Level on page 96).

• Check that the speaker hasn’t been set to NO (see Speaker Setting on

page 95).

• The channel may not be recorded in the source. By using one of the advanced

effect listening mode, you may be able to create the missing channel (see

Listening in surround sound on page 53).

Sound is produced from

analog components, but not

from digital ones (DVD, LD,

CD-ROM, etc.).

• Check that the input signal type is set to DIGITAL (see Choosing the input

signal on page 58).

• Make sure that the digital input is assigned correctly for the input jack the

component is connected to (see The Input Setup menu on page 39).

• Check the digital output settings on the source component.

• If the source component has a digital volume control, make sure this is not

turned down.

• Make sure that the multichannel analog inputs are not selected. Select any

other input function.

No sound is output or a noise

is output when Dolby Digital/

DTS software is played back.

• Check that your DVD player is compatible with Dolby Digital/DTS discs.

• Check the digital output settings of your DVD player. Make sure that the DTS

signal output is set to On.

• If the source component has a digital volume control, make sure this is not

turned down.

No sound when using the

HOME MENU or STATUS

menu.

• If the HDMI input function is selected, sound is muted until exiting either

menu.

• If sound is muted in the sub zone (ZONE 2), it will be restored after exiting the

HOME MENU.

Symptom Remedy

VSX-1019_KU.book 104 ページ２００９年２月１７日　火曜日　午前１１時５６分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-1019AH-K Seite 104

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSX-1019AH-K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info