Bedienungsanleitung Pioneer VSX-1019AH-K (Seite 106 von 128) (Englisch)

455217

106

Zoom out

Zoom in

Vorherige Seite

1/128

Nächste Seite

Additional information12

106

Video

Settings

Symptom Remedy

No image is output when an

input is selected.

• Check the video connections of the source component (see page 28).

• For HDMI, or when digital video conversion is set to OFF and a TV and another

component are connected with different cords (in Setting the Video options on

page 67), you must connect your TV to this receiver using the same type of video

cable as you used to connect your video component.

• Make sure the input assignment is correct for components connected using

component video or HDMI cables (see The Input Setup menu on page 39).

• Check the video output settings of the source component.

• Check that the video input you selected on your TV is correct.

• Some components (such as video game units) have resolutions that may not

be converted. If adjusting this receiver’s Resolution setting (in Setting the Video

options on page 67) and/or the resolution settings on your component or

display doesn’t work, try switching Digital Video Conversion (in Setting the Video

options on page 67) OFF.

Can’t record video. • Check that the source is not copy-protected.

• The video converter is not available when making recordings. Check that the

same type of video cable is used for connecting both the recorder and the video

source (the one you want to record) to this receiver.

Noisy, intermittent, or

distorted picture.

• Sometimes a video deck may output a noisy video signal (during scanning,

for example), or the video quality may just be poor (with some video game units,

for example). The picture quality may also depend on the settings, etc. of your

display device. Switch off the video converter and reconnect the source and

display device using the same type of connection (component or composite),

then start playback again.

Symptom Remedy

The Auto MCACC Setup

continually shows an error.

• The ambient noise level may be too high. Keep the noise level in the room as

low as possible (see also Problems when using the Auto MCACC Setup on

page 39). If the noise level cannot be kept low enough, you will have to set up

the surround sound manually (page 94).

• When using only one surround back speaker, connect it to the SURROUND

BACK L (Single) terminals.

• To use a 5.1-channel speaker set, use the surround speakers for the surround

channel, not the surround back channel.

• Make sure there are no obstacles between the speakers and the microphone.

• If Reverse Phase is displayed, try the following:

– The speaker’s wiring (+ and –) may be inverted. Check the speaker

connections.

– Depending on the type of speakers and their installation conditions, Reverse

Phase may be displayed even if the speakers are properly connected. If this

happens, select GO NEXT and continue.

– If the speaker is not pointed to the microphone (listening position) or when

using speakers that affect the phase (dipole speakers, reflective speakers, etc.),

it may not be possible to properly identify the polarity.

VSX-1019_KU.book 106 ページ２００９年２月１７日　火曜日　午前１１時５６分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-1019AH-K Seite 106

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSX-1019AH-K

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info