Bedienungsanleitung Pioneer VSX-C100 (Seite 29 von 60) (Englisch)

455260

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

English

Fine Tuning Your Surround Sound

LFE attenuator setting

Dolby Digital and DTS audio sources include ultra-low

bass tones. Set the LFE attenuator as needed to prevent

the ultra-low bass tones from distorting the sound from

all the active speakers.

Follow steps 1&2 on page 27 (if necessary).

Use the +/– buttons to choose the attenuation

level 0 dB, 10 dB or LFE OFF.

0 dB

No attenuation.

10 dB

LFE volume is reduced.

LFE OFF

LFE channel is off.

Press SETUP to advance to the next receiver setting

mode.

Press ENTER if you want to exit the setting

mode.

• The default setting is “0 dB”.

Front speakers distance setting

Set the distance from the front speakers to the listening

position.

Follow steps 1&2 on page 27 (if necessary).

Use the +/– buttons to choose the distance of

the front speakers from the main listening

position (within a range from 0.3 m to 9.0 m).

Press SETUP to advance to the next receiver setting mode.

Press ENTER if you want to exit the setting

mode.

• The default setting is “1.8 m”.

• One step equals about 0.3 m.

• If you do the Room Setup (see page 26) after the

settings here, those will take precedence.

Center speaker distance setting

Set the distance from the center speakers to the listening

position.

Follow steps 1&2 on page 27 (if necessary).

Use the +/– buttons to choose the distance of

the center speaker from the main listening

position (within a range from 0.3 m to 9.0 m).

Press SETUP to advance to the next receiver setting mode.

Press ENTER if you want to exit the setting

mode.

• The default setting is “1.5 m”.

• One step equals about 0.3 m.

• When “CENTER –” is selected in Center speaker

setting, the

Center speaker

distance cannot be set.

• If you do the Room Setup (see page 26) after making

the settings here, those will take precedence.

SUBWF 100 Hz

Sends bass frequencies below 100 Hz to the

subwoofer.

SUBWF PLS

Adds extra bass to the soundtrack.

SUBWF – – –

Select if you didn’t connect a subwoofer.

Press SETUP to advance to the next receiver setting

mode.

Press ENTER if you want to exit the setting

mode.

• The Subwoofer setting will appear automatically,

depending on whether you have connected a

subwoofer or not.

• The default setting is “200 Hz”.

• You can only select PLS when the front speakers are

set to Large (L).

• If the all the speakers are set to Large (L) you can

only select 100 kHz, PLS or off (– – –) for the

Subwoofer.

• Setting the front speakers to Small (S) means you

will use a subwoofer, thus its setting cannot be

turned off. In this case make sure you set the

subwoofer and choose its cutoff frequency.

• There are some cases where no sound will come from

the subwoofer even if it is (this depends on the

speaker setting, the listening mode and/or the kind of

source material).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-C100 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSX-C100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info