Bedienungsanleitung Pioneer VSX-C100 (Seite 30 von 60) (Englisch)

455260

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

Fine Tuning Your Surround Sound

Dual mono setting

Dual mono has two different audio channels in it. You

can use it to listen to soundtracks that have one

language on one channel and a different language on

the other.

The dual mono setting can only be used when listening

to discs that have dual mono software encoded in them,

for example some Dolby Digital discs. As of now these

are not that widely used.

The

ch1 setting plays channel 1 through your center

speaker. If you have selected no Center speaker in the

speakers setting (or are in a 2 ch listening mode) then

you will hear ch1 out of both front speakers. The

ch2

setting plays channel 2 through your center speaker. If

you have selected no Center speaker in the speakers

setting (or are in a 2 ch listening mode) then you will

hear channel 2 out of both front speakers. In the

L. c1

R. c2 setting the speakers will play the soundtrack

independently of each other. The left front speaker will

play channel 1 and the right front speaker will play

channel 2.

Follow steps 1&2 on page 27 (if necessary).

Use the +/– buttons to choose the Dual mono

setting (ch1, ch2 or L. c1 R. c2).

Press SETUP to advance to the next receiver setting mode.

Press ENTER if you want to exit the setting

mode.

• The default setting of this feature is “ch1”.

Surround speakers distance setting

Set the distance from the surround speakers to the

listening position.

Follow steps 1&2 on page 27 (if necessary).

Use the +/– buttons to choose the surround

speakers from the main listening position

(within a range from 0.3 m to 9.0 m).

Press SETUP to advance to the next receiver setting mode.

Press ENTER if you want to exit the setting

mode.

• The default setting is “1.8 m”.

• One step equals about 0.3 m.

• When “SURR. –” is selected in Surround speakers

setting, the Surround speakers distance cannot be set.

• If you do the Room Setup (see page 26) after the

settings here, those will take precedence.

Dynamic range control setting

Dynamic range is the difference between the loudest and

softest sounds in any given signal. The dynamic range

control helps you playback sounds so the quieter sounds

are audible yet the louder sounds don’t get distorted. It

does this by compressing the dynamic range. When

watching a movie at low volume, setting this function

enables low level sounds to be heard more easily but you

won’t be jolted by louder sounds.

Follow steps 1&2 on page 27 (if necessary).

Use the +/– buttons to choose the dynamic

range control (OFF, MAX, or MID).

Dynamic range control is operative only when a

Dolby Digital soundtracks with this feature encoded

into it is being played back. For other sources use the

MIDNIGHT mode (see page 35) to achieve the same

effect.

Press SETUP to advance to the next receiver setting mode.

Press ENTER if you want to exit the setting

mode.

• The default setting is “OFF”.

• When listening at high volume, set to OFF.

• For best results at low volumes, set to “MAX” for

maximum dynamic range compression.

• Dynamic range control is expressed as DRC in the

display.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pioneer VSX-C100 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pioneer VSX-C100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info