772288

Polisport Bubbly Mini Seite 7

7
Zoom out
Zoom in
Vorherige Seite
1/68
Nächste Seite
| 4 | www.polisport.com
1. Turn the child seat upside down as shown in the image. Cut the plastic
straps that hold the mounting block (I).
2. Remove the metallic bracket (H) from the seat by cutting the straps.
Disengage and remove the metallic bracket (H) from the child seat, pulling
it upwards.
3. Use the Allen key No. 5 (I5) to loosen and remove the metal mounting
plate (J1).
4. Hold the metallic bracket (H) the same as in the picture and pass it
through the opening in the child bicycle seat.
5. Insert the metallic mounting plate (J1) on the grooves of the child
bicycle seat, and close it as indicated in the picture.
6. Place the washer (J3) on the screw (J2). Then tighten securely with the
key (I5). Tighten tightly so that the metal bracket (H) is securely fastened.
This step is extremely important for the safety of the child.
7. Remove the screws (I1) on the mounting block (I), with the Allen key
no. 5 (I5).
8. Before placing the block onto the frame, make sure that the protective
rubber (I8) is correctly positioned on front of the block.
9. Place the main body of the mounting block (I2) on the front of the
bicycle frame, and then place the metallic mounting plate (I4).
Note: If they are cables in this area make sure that they are correctly
positioned in the central groove of the metallic plate, (between the
protective rubber (I8) and the groove of the mounting plate (I4) and are
able to move freely).
10. Place the washer (I6) in the M8 screws (I1), and then screw them
on to the mounting block (I). Tighten the screws, with the Key (I5), so
that the mounting block (I) is secured but not fully tightened so that, if
necessary, you can adjust the height later. However, note that it should
be tight to make it easier to complete the next step. You need to tighten
the 4 screws diagonally and in stages. Check the safety of the fasteners
regularly.
11. Place the edges of the metallic bracket (H) at the holes of the
mounting block (I) until you hear a click indicating the lock, and until the 2
green safety device indicators pop up on the front of the mounting block.
The child bicycle seat will only be properly installed when the 2 green
safety device indicators are visible. This step is extremely important for the
child’s safety.
12. After adjusting the height and positioning of the seat, hand tighten
the mounting block (I) to ensure that it cannot move. This tightening must
be manual and is extremely important for the safety of the child. Make
sure that the mounting block (I) is firmly attached. You need to hand tight
the 4 screws diagonally, with the same force and in stages (I5).
13. (B) To place the child in the seat, first open the belt. Start by pressing
the releases on the sides of the safety buckle (B4) and pull the buckle (B1)
upwards, so that it slides out of the socket (B5). Place the child in the seat.
Insert the safety buckle (B1) in its socket again (B5). Make sure that the
buckle socket (B5) is correctly positioned and does not hurt the child.
Next, adjust the belt to the size of the child to ensure that the child is
firmly secured. First adjust the height of the belt. To do this, pull the straps
according to the size of the child. Before starting the journey, always check
that the child is secured and that the belt is snug but not so tight that it
hurts the child. We recommend that the child’s helmet be put on after the
belt is adjusted. Note: Always use the restraint system.
(B.A) To place the child in the seat, first fully extend the belt straps (B),
sliding the adjusters (B2). This makes it easier to put the helmet when the
child is in the seat. Do the same for the other side. To put the child in the
seat, open the lock (B1) of the safety belt (B) pressing the three buttons of
the lock (B1) as indicated. Before starting your ride, make sure the seat belt
is properly adjusted and that it does not hurt the child. This adjustment
is made by sliding the belt adjustors (B2). Note: Always use the restraint
system.
14. To adjust the height of the footrest (E) to fit your child, release the
footrest (E) from the seat (A) by pressing the two fasteners together and lift
• This front baby seat must not be mounted to bicycles fitted with rear
shock absorbers.
• This front baby seat must not be mounted to a racing bicycle with drop
handlebar.
• This front baby seat must not be mounted to Motorized Vehicles such as
Mopeds and Scooters.
• This front baby seat must not be mounted in bicycles with triangular,
square or carbon fiber frames.
• This front baby seat must be mounted on non-moving parts of the
bicycle.
• This front baby seat must be assembled on bicycles with round and oval
frames with diameters ranging from Ø28 to Ø40 mm.
• The front baby seat must be assembled on bicycles with wheels with
diameters of 26” to 29”.
• This front baby seat is only suitable for carrying children with a maximum
weight of 15 Kg (and children with recommended ages ranging from 9
months to 3 years of age - with the weight as the decisive variable).
• The total weight of the cyclist and the child transported must not exceed
the maximum permitted load permitted for the bicycle. Information on
the maximum load can be found in the operating instructions of the
bicycle. You can also contact the manufacturer for this question.
• The front baby seat may only be mounted on a bicycle suitable for the
attachment of such additional loads.
• The position of the front baby seat must be adjusted so that the bicycle
rider does not touch the child bicycle seat with the feet when in motion.
• It’s very important to adjust correctly the seat and its component parts
for optimum comfort and safety of the child. It’s also important that the
seat does not slope forward, so that the child does not tend to slide out of
it. It’s also important that the backrest slope backward slightly.
• Check if all parts of the bicycle function correctly with the front baby
seat mounted.
• Check the instructions of the bicycle, and If you have any doubts on
fitting the front baby seat to your bicycle, please contact your bicycle
supplier for further information.
ASSEMBLY INSTRUCTIONS
TECHNICAL FEATURES
A. Main seat
B/B.A. Safety belt
B1/B.A1. Safety lock
B2. Belt adjuster
B3. Central belt adjuster
B4. Safety buckle releases
B5. Safety buckle socket
C. Back cushion
D. Footrest strap
E. Footrest
F. Seat cushion
G. Batch serial number
H. Metallic bracket
I. Mounting block
I1. Screws M8x45
I2. Plastic mounting block
I3. Release button
I4. Metallic mounting plate
I5. Allen key no. 5
I6. Lock washer M8x16
I7. Safety device indicator
I8. Protective rubber
J. Metallic mounting Kit
J1. Metallic mounting plate
J2. M8x16 screw
J3. M8 washer
TABLE OF CONTENTS OF PRODUCT
For child safety and for your peace of mind, Polisport has developed the
perfect child carrying solution that’s suitable for a wide range of adult
bicycles.
Our ergonomic child seats are all built with safety and comfort as the
primary goals.
In this manual, you will find information on attaching the front baby seat
to the frame of your bicycle.
Carefully read the manual for a safe and correct installation of the front
baby seat.
FRONT BABY SEAT FOR BICYCLE
FRAME MOUNTING SYSTEM
EN
… 7 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Polisport Bubbly Mini wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info