Bedienungsanleitung Practixx PX-RRM-600WI (Seite 36 von 68) (Deutsch, Englisch, Französisch)

782000

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

28 | GB

8.3.1.2 Fasten the boundary wire (11) with the

wire pegs (12)

m NOTE:

The distance between the wire pegs (12) must not

exceed 80 cm (Fig. 12).

• Place the boundary wire (11) on the grass at a dis-

tance of 30 cm or 8 cm from the outer edge (Fig.

6/7).

• Fix the boundary wire (11) at least every 80 cm using

a wire peg (12) (Fig. 12).

• Knock the wire pegs (12) into the ground (Fig. 13)

with the help of a hammer (not included in the

scope of delivery).

• In case of uneven or curved conditions, the dis-

tance between the wire pegs (12) must be reduced

accordingly.

8.3.2

Laying the boundary wire around obstacles

(islands) (Fig. 14)

m NOTE:

For large and heavy objects listed below as exam-

ples, an “island installation” is not necessarily re-

quired:

- Tree

- Raised bed

- Large/heavy plant buckets

- Greenhouse

- Garden shed

To protect delicate/small objects from damage, lay

the boundary wire (11) as follows:

• Run the boundary wire (11) along the outer edge

until you have reached the point with the short-

est distance (but at least 0.8 m) between the outer

edge and the obstacle.

• Lay the boundary wire (11) like a “supply line” along

the shortest path to the obstacle.

• Lay the boundary wire (11) at a distance of 30 cm or

8 cm (see point 8.3.1) around the obstacle.

• Lay the cable along the “feed line” back to the out-

er edge.

m ATTENTION!

DO NOT ALLOW THE BOUNDARY WIRE (11)

TO CROSS. The maximum distance between

the boundary wires is 5 mm.

• Continue to lay the cable along the outer edge.

8.3.3 Demarcation of slopes >35% (Fig. 15)

• The boundary to slopes >35% must be at least 40

cm, as shown in Fig. 15.

• If you do not maintain this distance, there is a risk

that the robot mower (1) will drive out of the demar-

cated area.

Thus, no function is possible any more, as the ro-

bot no longer has any orientation.

m NOTE

When you have completely staked out the work-

ing area, connect the boundary wire (11) to the

charging station (10) as described in point 8.2.

m ATTENTION

Fix the charging station (10) in place with the

help of a hammer (not included in delivery) and

the anchor pegs (13) only after you have staked

out the complete working area.

8.4 Connecting the charge station (10) (Fig. 16)

• Connect the 2-pin connector to the charging sta-

tion (10) as shown in gure 16 and screw it in place.

• Then plug the mains plug into the socket.

m ATTENTION

Make sure that the boundary wire (11) is correct-

ly routed and the power supply unit (14) is cor-

rectly connected to the charging station (10) be-

fore connecting the plug to the mains.

If the charging station (10) is connected to the mains,

an LED lights up on the rear part of the charging sta-

tion (10). (see Fig. 17).

8.4.1 Description of the status LED (Fig. 17)

LED

status

Meaning Measure

Does

not illu-

minate

No power

supply

Make sure that

the mains cable is

properly connect-

ed to the charging

unit and that the

charging unit is con-

nected to a suitable

power supply

Illumi-

nates

green

The boundary

wire is connected

correctly.

The robot is fully

charged.

Flashes

green

The robot is

charging.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Practixx PX-RRM-600WI Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info