Bedienungsanleitung Pro-form 400 ZLT - PETL49910 (Seite 14 von 28) (Englisch)

553944

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

HOW TO TURN ON THE POWER

IMPORTANT: If the treadmill has been exposed to

old temperatures, allow it to warm to room tem-

perature before turning on the power. If you do not

o this, you may damage the console displays or

other electrical components.

Plug in the power cord (see

page 12). Next, locate the

power switch on the tread-

mill frame near the power

cord. Make sure that the

switch is in the reset

position.

IMPORTANT: The console features a display demo

mode, designed to be used if the treadmill is dis-

played in a store. If the displays light as soon as

you plug in the power cord and press the power

switch into the reset position, the demo mode is

turned on. To turn off the demo mode, hold down

the Stop button for a few seconds. If the displays

remain lit, see THE INFORMATION MODE on page

17 to turn off the demo mode.

Next, stand on the foot rails of the treadmill. Find the

clip attached to the key (see the drawing on page 13)

and slide the clip onto the waistband of your clothes.

Then, insert the key into the console. After a moment,

the displays will light. IMPORTANT: In an emergency

situation, the key can be pulled from the console,

causing the walking belt to slow to a stop. Test the

clip by carefully taking a few steps backward; if the

key is not pulled from the console, adjust the posi-

tion of the clip.

HOW TO USE THE MANUAL MODE

1. Insert the key into the console.

See HOW TO TURN ON THE POWER above. The

treadmill will rise to the maximum incline level and

then return to the minimum incline level.

2. Select the manual mode.

When the key is in-

erted, the manual

mode will be selected. If

ou have selected a

workout, reselect the

manual mode by press-

ing one of the Workouts buttons repeatedly until

only zeros appear in the displays.

3. Start the walking belt.

To start the walking belt, press the Start button, the

Speed increase button, or one of the numbered

speed buttons.

If you press the Start button or the Speed increase

button, the walking belt will begin to move at 2

Km/H. As you exercise, change the speed of the

walking belt as desired by pressing the Speed in-

crease and decrease buttons. Each time you press

one of the buttons, the speed setting will change

by 0.1 Km/H; if you hold down the button, the

speed setting will change in increments of 0.5

Km/H. Note: After you press the buttons, it may

take a moment for the walking belt to reach the se-

lected speed setting.

If you press one of the numbered speed buttons,

the walking belt will gradually change speed until it

reaches the selected speed setting.

To stop the walking belt, press the Stop button.

The time will begin to flash in one of the displays.

To restart the walking belt, press the Start button

or the Speed increase button.

4. Change the incline of the treadmill as desired.

To change the incline of

the treadmill, press the

Incline increase and de-

crease buttons. Each

time you press one of

the buttons, the incline

will gradually increase or decrease until it reaches

the selected incline setting.

Reset

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Pro-form 400 ZLT - PETL49910 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Pro-form 400 ZLT - PETL49910

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info