Bedienungsanleitung Proficare HL 3116 (Seite 13 von 74) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

814769

Zoom out

Zoom in

Vorherige Seite

1/74

Nächste Seite

PC-HL3116_IM 29.06.23

• Make sure beforehand that there are no cables in the wall that

could be damaged during installation.

• Drill the holes at a height of 2 m above the oor.

• The distance to the ceiling and walls should be at least 30 cm.

1. Drill two holes with a diameter of 6 mm at a dis-

tance of 315 mm.

2. Provide the holes with the wall plugs and the

screws. Leave the screws protruding about 10 mm from the wall.

3. Hang the appliance with the recesses (A) on the

screws. Now push the appliance in direction (B) to x it.

- When you want to take the appliance off the wall

again, slide it from (B) to (A) and then lift the appliance off the

wall.

Remote control

The lithium cell in the battery compartment

of the remote control has been secured with

a plastic lm for transport. This prolongs the

life of the battery. Before using the remote

control for the rst time, the plastic lm must be removed so

that it is ready for use.

When operating the appliance, make sure that there is a

clear line of sight between the remote control and the sen-

sor in the display of the appliance. When the range of the

remote control decreases, the battery must be changed. To

change the battery, proceed as follows:

1. Press the lock in the direction of the

arrow (1).

2. Pull the holder for the button cell out of

the remote control (2).

3. Replace the cell with a battery of the

same type (CR 2025). Make sure that

the polarity is correct.

4. Push the holder back into the battery compartment until

it clicks into place.

Electric Connection

1. Make sure the voltage of the appliance (see rating label)

matches the mains voltage to be used.

2. Set the mains switch on the right side of the appliance to

the O position.

3. Connect the mains plug with a properly installed earthed

socket.

Switching the Appliance On

• Set the mains switch on the right-hand side of the appli-

ance to position I. The appliance starts the motor to close

the air ap, which may still be open. The appliance then

switches to standby mode.

• The appliance is operated via the remote control.

Easy Operation

You can also switch the appliance on and off without the

remote control. To do so, press the START / STOP button

next to the mains switch.

1. Press the button to switch the appliance on.

The appliance switches on with the temperature setting

HIGH, fan (FAN) and swinging of the air ap (SWING).

2. Press the button again to switch the appliance off. The

FAN mode is started for 30 seconds and the air ap is

closed. The appliance then switches to standby mode.

Notes for Use

• The appliance is equipped with overheating protection.

When the ambient temperature reaches 51 °C, the

appliance switches off.

• Avoid opening doors and windows during heating opera-

tion, as this will impair the heating effect.

• The current ambient temperature is displayed.

• The appliance always starts in fan mode.

• Settings can only be made during operation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Proficare HL 3116 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info