Bedienungsanleitung Protool AGP 230-26 R (Seite 19 von 148) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

490682

Zoom out

Zoom in

Vorherige Seite

1/148

Nächste Seite

The emission values speciﬁ ed (vibration,

noise) were measured in accordance with

the test conditions stipulated in EN 60 745

and are intended for machine comparisons.

They are also used for making preliminary

estimates regarding vibration and noise

loads during operation.

The emission values speciﬁ ed refer to the

main applications for which the power tool

is used. If the electric power tool is used for

other applications, with other tools or is not

maintained sufﬁ ciently prior to operation,

however, the vibration and noise load may

be higher when the tool is used.

Take into account any machine idling times

and downtimes to estimate these values

more accurately for a speciﬁ ed time period.

This may signiﬁ cantly reduce the load dur-

ing the machine operating period.

6 Installation of

protective elements

WARNING

Before performing any maintenance

work on the tool, always remove the

plug from the electrical mains socket.

WARNING

The grinder may only be used with

the protective cover in place and the

auxiliary handle afﬁ xed.

6.1 Cover

Loosen the clamping lever [2-5].

Fit the cover [2-1] onto the spindle collar

[2-4]. The guiding pad [2-6] must ﬁ t into

the groove on the spindle collar.

Put the cover [2-1] into a suitable operating

position and ﬁ rmly tighten the collar with

the clamping lever [2-5].

Due to the safety reasons, it is necessary to

tighten the ensioning nut [2-7] by means

of torque moment 3 + 0.5 Nm.

Protective cover for cutting

For cutting metal, always work with the pro-

tective cover for cutting [2-2].

The protective cover for cutting [2-2] is

mounted in the same manner as the pro-

tective cover [2-1].

Suction cover

Loosen bolt [2-8].

Place the suction cover [2-3] on the spin-

dle collar [2-4]. The guide pad [2-6] must

be inserted into the groove on the spindle

collar.

Turn the grinder to an appropriate work

position and ﬁ rmly tighten the collar using

the bolt. For this use a 6-sided wrench.

A sufﬁ ciently wide travel of the cover pre-

vents deviation of the angle grinder from

the level of the cut.

Carefully read the user’s manual for the use

of the suction cover.

6.2 Auxiliary handle

Special construction “VIBRASTOP” regulates

the vibrations with auxiliary handle [1-9].

Auxiliary handle can be screwed from the

left or right side of gearbox [1-7]. Some

operations may require the handle screwed

to the top of gearbox.

6.3 Rotating handle

By turning the main handle by 90° to the

left or right you achieve better handling of

the tool.

Press the handle arrest button [1-3] and turn

the holder to the working position, where the

arrest button must again lock in.

WARNING

The grinder must not be used in the

when the rotating handle is the ar-

rested position.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Protool AGP 230-26 R Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info