Bedienungsanleitung Protool AGP 230-26 R (Seite 21 von 148) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

490682

Zoom out

Zoom in

Vorherige Seite

1/148

Nächste Seite

Starting current limiting

The electronically controlled smooth start

takes care that the machine starts without

jerk. As a result of the machine’s reduced

starting current, a 10 A fuse is sufﬁ cient.

Protection in case of disk locking

When cutting disk is used for cutting, it

may get locked in the cut. To reduce the

risk of injury or burning of the machine, the

electronics reacts to rapid growth of load

by turning the engine off. For restart turn

the machine off and then on again.

9 Work instructions

► Check that the label on the disc shows

the permissible peripheral speed or per-

missible revolution speed.

► If the permissible revolution speed is

given on the disc, it must not be lower

than the highest no-load speed of the

grinder.

► Discs with a permissible peripheral speed

of 80 m.s

–1

and higher may be used.

► Test new cutting discs by letting them

run for about one minute with no load.

► Unbalanced or vibrating discs should not

be used and should be discarded.

► Protect grinding discs from shock, impact

and lubricants.

► If the grinding and cutting wheels are

worn down to the mark on the wheel

protective cover (see the arrow sign),

they should be replaced with new ones.

This maintains the optimum grinding and

cutting performance of the machine (pe-

ripheral speed of the grinding and cutting

wheels).

► To cut steel, concrete or stone using a

grinding disc use the protective cover for

dividing.

► For grooving and cutting of concrete

or stone it is recommended to use the

suction cover PROTOOL DCC-AGP 230

together with an appropriate PROTOOL

dust vacuum cleaner. Use diamond discs

PROTOOL All-D230 Premium with this

cover.

10 Maintenance

- The unit should be stored in a dry place

where it is protected against freezing.

- The ventilation holes [1-5] on the motor

casing must not get blocked up.

- The cable may only be replaced in a spe-

cialised electrical workshop qualiﬁ ed to

perform such work.

After approx. 200 hours of use the following

maintenance work must be performed:

- Check the length of the brushes. Brushes

shorter than 5 mm should be replaced.

- The machine turns itself off automati-

cally when the brushes are worn out. The

machine must be sent to a service centre

for maintenance.

WARNING

To preserve the protection class the

machine must undergo a safety in-

spection; this must be done in a spe-

cialised electrical workshop qualiﬁ ed

to perform such work.

- Service – see enclosed sheet.

11 Environmental

Protection / Disposal

Power tools, accessories and packaging

should be sorted for environmental-friendly

recycling.

Only for EC countries:

Do not dispose of power tools into

household waste!

According to the European Directive

2002/96/EC on waste electrical and elec-

tronic equipment and its incorporation into

national law, power tools that are no longer

suitable for use must be separately collect-

ed and sent for recovery in an environmen-

tal-friendly manner.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Protool AGP 230-26 R Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info