490682
20
Zoom out
Zoom in
Vorherige Seite
1/148
Nächste Seite
20
7 Fitting the grinding disc
7.1 Assembly with the standard
clamping nut
Clean the lower ange [3-1] and the clamp-
ing nut [3-3], as well as the clamping sur-
face on the grinder disc.
Place the backing ange [3-1] on the grind-
er spindle [1-8].
Fit the grinding disc [3-2]. The backing
ange [3-1] must t the hole of the grind-
ing disc [3-2] exactly.
Press in the spindle locking button [1-6].
WARNING
Make sure that the grinder spindle is
not turning before pressing the spin-
dle locking button.
Turn the grinding disc [3-2] / grinder spin-
dle [1-8], until the spindle lock [1-6] en-
gages.
Firmly tighten the clamping nut [3-3] using
the wrench [3-5].
Before switching on check that the grinder
disc can rotate freely.
7.2 Assembly with the FASTFIX
quick-action xing nut
Some versions of the machine are tted
with a FASTFIX quick-action nut, which al-
lows the clamping of the grinding wheel
without using tools (see the notice on the
packaging – FASTFIX). This xing nut can
be tightened and loosened by hand only (do
not use any additional xing tool!).
The mounting of the grinding wheel is car-
ried out in the same way as in the machine
version without the quick-action xing nut
but after pressing the spindle clamp the
quick-action xing nut [3-4] can only be
tightened by hand.
WARNING
Do not tighten the quick-action xing
nut without the wheel. This might re-
sult in damage to its mechanism.
8 Activation
WARNING
Before performing any maintenance
work on the tool, always remove the
plug from the electrical mains socket.
Check that the information on the manufac-
turing label complies with the actual power
supply voltage.
Equipment marked with 230 V can also be
connected to 220 V / 240 V.
Check that the plug type is the same as the
socket type.
8.1 Switching on and off
Push the safety lock-off lever [1-2] forwards
to release the On/Off switch lever [1-1].
At the same time, press the on-off switch
lever [1-1] to start the grinder and release
it to stop.
8.2 Continuous use
Push the safety lock-off lever [1-2] forwards
to release the On/Off switch lever [1-1].
At the same time, press the on-off switch
lever [1-1] and push the safety lock-off le-
ver [1-2] forwards.
To turn off continuous operation, press and
release the on-off switch [1-1] again [1-1].
8.3 Control electronics
Increases productivity, life service of the
grinder, comfort at work, as well as quality
and safety of work. Provides the following
functions:
Protection against re-start
If power failure occurs during work (if the
mobile power supply plug is pulled out, if
circuit breaker fails, etc.), and the switch
stays locked in the ON position, the ma-
chine does not turn on automatically once
the power supply recovers. To restart the
grinder, its switch needs to be turned off
rst and then turned on again.
Slow start
After the grinder is turned on, control elec-
tronics secures gradual start to operating
rpm, without pointless strokes. This reduc-
es wear of gearing, thus increasing the life
service of the grinder.
20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Protool AGP 230-26 R wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info