Bedienungsanleitung Proxxon DSH-E (Seite 12 von 20) (Englisch)

782198

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

- 12 -

8.4 Adjust and set angle display (fig. 2):

1. Slightly loosen toggle 1 (fig. 2) and fold saw table 2 up to

stop screw 3.

2. Clamp saw blade 4! See the corresponding section 8.7.1 of

these instructions. Caution! Mains plug must not be

connected.

3. Using an angle 5 on the saw table 2, check the right-hand

angle to the saw blade. The stop screw is preset. If this still

has to be adjusted, you can adjust the setting yourself

using an Allen key 7, as shown in fig. 2, once the counter

nut has been loosened. After correct setting, tighten the

counter nut. Make sure that the stop screw does not go

out of position in this process.

4. Check the “zero” setting of the bevel indicator 8, if

necessary, correct after the fastening screw has been

loosened. For precise working, carry out sawing sample.

5. Saw a sample from a piece of wood and check the angle

again, if necessary adjust the saw table 2, indicator 8 or

stop screw 3 as shown in fig. 2.

8.5 Assembling the air nozzle (fig. 3):

1. Take parts for securing the air nozzles from the attached bag.

2. Screw the knurled screw 1 (fig. 3) with clamping pieces 2

into the saw frame.

3. Introduce the air nozzle pipe 3 (fig. 3) into the hole on the

opened clamp pieces, adjust the pipe and slightly tighten

the toggle 1.

4. Place the air hose 4 (fig. 3) on pipe 3 and nipple 5.

8.6 Connecting the vacuum cleaner (fig. 4):

1. Place the vacuum hose 1 of the vacuum cleaner in the

connecting piece 2.

2. Switch on the vacuum cleaner before sawing so that the

sawdust is vacuumed and the suction device does not get

blocked. For practical reasons, the PROXXON suction

control device is recommended.

8.7 Saw blades

CAUTION!

Always remove the mains plug before performing the activities

described here.

8.7.1 Clamping in the saw blade (fig. 5a and 5b):

Standard blades with cross pins or plain ended blades

without cross pin can be clamped into the saw blade mount.

Replace damaged or worn saw blades immediately. They

represent a safety risk and worsen the work result. The best

cutting performance and precision can only be achieved with

perfect saw blades.

Use PROXXON original saw blades and carefully select

suitable saw blades for the intended purpose and material to

be cut. With Proxxon, there are also various fine toothings, flat

and round blades, and some with and without cross pin. You

will find suggestions in these instructions.

8.7.2 Saw blades with cross pin (fig. 5a).

Saw blades with cross pin are particularly suitable for working

with many closed inside cuts. The saw blade can be quickly

and comfortably removed from the upper mount, looped

through the work piece and repositioned. You will find more

precise information in the section "Inside cuts".

CAUTION!

Saw blades with cross pins may only be hung in position. Do

not clamp the saw blades with the cross pin additionally by

means of the cheese-head screws. Risk of fracture!

1. Position the level for the quick tensioning clamp 4 to the

front!

2. Place saw blade 1 with the teeth pointing downwards

through the table opening 2 and fit in the bottom mount 3.

3. Press lightly on the top arm 5 and fit blade in the upper

mount 6, see fig. 5a).

4. Release arm and position the lever of quick tensioning

clamp 4 to the rear.

5. If required, finely set the saw blade clamp as described

under 8.7.4.

8.7.3 Saw blades with flat ends (hand or leaf saw blades,

see fig. 5b):

1. Position the lever for the quick tensioning clamp 4 to the

front!

2. Place saw blade 1 with the teeth pointing downwards

through the table opening 2 and fit in the bottom mount 3.

Then clamp the blade in the mount by tightening the

cheese-head screw 4 with the supplied Allen key with

T-handle 5.

3. Press lightly on the upper arm 6, introduce the saw blade

into the upper mount 7 and fix by tightening the wingnut 8.

4. Position the lever for the quick tensioning clamp 9 to the

rear!

5. If required, finely set the saw blade clamp as described

under 8.7.4.

8.7.4 Finely setting the correct saw tensioning (fig. 6):

Correct saw tensioning is an essential factor for a clean work

result. This must, therefore, be carefully set. If over or

Proxxon_BedienAnl_DSH_US_Bel 10.06.2005 14:20 Uhr Seite 12

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Proxxon DSH-E Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Proxxon DSH-E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info