Bedienungsanleitung Proxxon FET (Seite 13 von 24) (Englisch)

782211

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Setting up the saw

Unpacking

Caution!

Please note that transport blocks have been at-

tached to the device during packing to avoid dam-

age during transportation. Make sure you remove all

of them before commissioning! Carefully read

through the instructions and especially observe the

following chapter!

A transport block made of cardboard is inserted on

the inside of the saw. This must be removed before

initial commissioning. How to swing up the upper

housing part is explained in the following chapter.

Swinging open the upper housing part

1. Please open the packaging box to unpack, care-

fully remove the saw and deposit it on a firm and

level surface.

2. Release the knurled screw 1 (fig. 2) and swing up

the upper housing part 2.

3. Permit the latch 3 to engage.

4. Before first commissioning, remove the cardboard

that was used as safeguard during the transport.

5. Release the latch 3 of the support and push the

upper housing part back down. Caution! Hold on

to the upper part when pushing down! Injuries

might be caused if the upper part drops down

unchecked.

6. Retighten knurled screw 1.

Fastening the saw

Generally the saw must be set up on a fixed and

level surface, ideally on a heavy workbench or a solid

table. To obtain a secure hold, your FET should be

screwed to the surface: For this purpose there are

four holes in the housing bottom so that fastening

screws can be screwed into them.

Note:

Safe and precise work is only possible with careful

fastening! Therefore, please proceed as follows:

Caution!

Make sure the mains plug is disconnected!

1. Swing up the upper part of the saw

2. Permit the latch to engage

3. Now you can see four hexagonal indentations on

the inside above the four screw holes in the hous-

ing bottom, see fig. 3. These are intended to re-

ceive M6 hexagon nuts, or the heads of M6 (or

similar) hexagon screws. Insert sufficiently long

screws 2 from inside through the opening in the

housing bottom and bolt them through the drill

holes that you previously drilled in the underlay 3.

1. Use a drilling template for the required hole spac-

ing. You will find a sketch with the dimensions at

fig. 4.

4. Then release the latch of the support and push the

upper housing part back down.

5. Do not forget to tighten the knurled screw 1 (fig. 2)!

Saw blade guard

Your FET is equipped with a saw blade guard. It is

designed in such a way that moves up as far as nec-

essary during sawing and then drops back into its

home position. It also adapts to the various adjusted

cutting depths.

Caution!

The saw blade guard is an important safety tool and

may in no way be tampered with or even dismantled.

Operating the saw without this guard is dangerous!

While setting up and transporting the saw, always

may sure that the upper saw blade cover is in its cor-

rect position. The free-lying, sharp teeth of the saw

blade pose a considerable risk of injury!

Secure the saw blade guard with the

splitting wedge (Fig. 5 and 5a)

Caution!

For packaging reasons, the saw blade guard and the

splitting wedge are not attached when the device is

delivered. However, assembly is rather simple:

Caution!

Make sure the mains plug is disconnected!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Proxxon FET Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info