Bedienungsanleitung Proxxon FET (Seite 14 von 24) (Englisch)

782211

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

1. Swing open the upper housing part and arrest.

2. Please note that the saw blade in its delivered

condition is in the lower position to guarantee ac-

cessibility to the drive unit. Otherwise, please pro-

ceed as explained in the section "Height

adjustment of the saw blade".

3. If the two screws 1 (fig. 5a) are not loose, please

release them slightly with a screwdriver. Insert the

orange-coloured saw blade guard with the splitting

wedge 2 in the saw blade slot 3 and insert behind

the little plate clip 4 like shown in Fig. 5). Please

ensure correct fit: The splitting wedge is seated on

the upper of the two screws 1 with its longer cut-

out (fig. 5a) up to the limit stop! Make sure the

splitting wedge is fitted correctly in any case! Only

tighten both screws 1 afterwards! After you have

tightened the screws, please check once more if

the splitting wedge is seated firmly and if the saw

blade can be turned freely.

4. Push the upper housing part back down and se-

cure with the knurled screw.

5. Set the desired saw blade position as described

further down in the chapter "Height adjustment of

the saw blade".

Settings

Height adjustment of the saw blade

To adapt the depth of cut, the position of the saw

blade can be regulated in the height. On the one

hand, this optimises the sawing performance, and on

the other hand the risk of injury is reduced due to the

restriction of the free saw blade part.

Caution!

Make sure the mains plug is disconnected for all ad-

justing work!

1. Release the larger knurled button 1 (fig. 6) at the

front operating plate and unscrew by a few revolu-

tions

2. The saw blade position can now be set using the

smaller knurled button 2: Turning clockwise will

adjust the blade upwards, and turning counter-

clockwise will adjust the blade downwards.

3. After the desired position is achieved, retighten the

knurled button 1.

Adjusting the saw blade tilt

The saw blade can be tilted to manufacture mitre

cuts. The desired value is set, or read, with the help

of the angle scale.

Caution!

Make sure the mains plug is disconnected for all ad-

justing work!

1. Release handwheel 1 (fig. 7).

2. Swing the saw blade to the right with the hand-

wheel.

3. Set or read off the desired angle with indicator 2 at

the angle scale 3.

4. Arrest the saw blade position by turning the hand-

wheel 1 shut

Extendable saw table

Caution!

Make sure the mains plug is disconnected for all ad-

justing work!

In order to place larger work pieces easily and se-

curely on the saw table, it has been designed as an

extendable saw table. The extension is quite simple:

Please note:

1. Use your finger to push the curry-coloured limit

stop edge 1 (fig. 8a) towards the back. This makes

it move out upwards.

2. Pull out the saw table 2 with the limit stop edge

into the desired position, see fig. 8b. If necessary,

support with the swivelling lever 3.

3. The small knurled screw 4 can be used to clamp

the extendable saw table into the desired position,

as necessary.

4. Now push the limit stop edge 1 back into its initial

position to achieve a plane surface. It is now pos-

sible to work with the saw. Please note: The limit

stop edge can also be used for larger work pieces

as a longitudinal stop, of course.

5. After completing your work, simply push the ex-

tendable saw table 2 back into the initial position.

If necessary, fold up the swivelling lever 3 before.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Proxxon FET Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info