Bedienungsanleitung Proxxon FET (Seite 16 von 24) (Englisch)

782211

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

adjustment of the longitudinal stop“) at the knurled

screw 6 (fig. 10d).

Caution!

Make sure the mains plug is disconnected for all ad-

justing work!

1. Make sure that locking handle 3 and knurled screw

4 are released.

2. Move the longitudinal stop 1 with the left edge 6

over the „0“ marking of the scale (either left or

right from the saw blade, depending on what is

needed for the task) as shown in fig. 10d and fix

the position by tightening knurled screw 4.

3. By turning the fine adjustment knob 7 bring the

scale with its arrested longitudinal stop into the

position where the side of the longitudinal stop

facing the saw blade just barely touches the saw

blade. Please carefully lift the saw blade guard 8 to

do so, if necessary!

Now the distance between the saw blade and limit

stop is „0“ as shown by the scale.

The limit stop can now be aligned with the help of

the scale, as described in the section „Adjusting the

longitudinal stop with the help of the scale“: The

value read from the scale now corresponds exactly

to the distance longitudinal stop – saw blade and

thus the desired width of the work piece.

Caution!

It is possible that before adjustment in the zero posi-

tion, the scale is in a position where the longitudinal

stop already touches the saw blade before the left

limit stop edge has reached the „0“ position on the

scale. In this case simply correct the scale position

with the fine adjustment knob 7.

Fine adjustment of the longitudinal stop

If after the sawing process it is necessary to make

minor changes to the position of the limit stop (de-

spite previous careful adjustment) to achieve the de-

sired width, it is possible to move the limit stop for a

small amount in the desired direction with the fine

adjustment knob 7, see fig. 10d. Please note: One

complete revolution will move the limit stop by 1 mm!

Caution! For this procedure, the lock handle 3 must

be released, but the knurled screw 4 must be tight-

ened. After adjustment is completed, the limit stop

must be tightened with locking handle 3 to continue

sawing!

Auxiliary stop

Appropriate use of the auxiliary stop is made to be

able to easily cut somewhat larger work pieces as

well. For this, the saw table must be extended first,

as described in the chapter „Extendable saw table“;

but the limit stop edge is not „sunk“ in the extend-

able part by „pressing in“ but simply stays outside.

The distance to the saw blade determines the sawing

width, which can therefore be varied depending on

by how much the saw table is pushed in, or ex-

tended. To saw, always fix the limit stop by tightening

the knurled screw. See fig. 8a.

Angle stop

If it is necessary to cut a board at right angles, or a

strip with mitre cut, then this can be sawn by using

the angle stop. This runs in the guides provided ei-

ther on the right or on the left of the saw blade, as re-

quired.

1. Insert the angle stop in the guide 1 to the right or

left of the saw blade, see fig. 11.

2. Release knurled screw 2, set the desired angle at

the scale 3 and retighten the knurled screw.

Working with the limit stop strip with

clamping piece for angle stop

Ideal, e.g. if many strips will be cut with mitre and

equal length, see fig. 12. The limit stop strip is con-

nected to the angle stop 2 to do this. The clamping

piece 3 is used as length stop.

Assembly and adjustment

Push the limit stop strip 1 into the guide of the angle

stop 2 (see fig. 13a) and insert together in the guide

in the saw table. Caution! The knurled screw must be

in the „released“ position otherwise the limit stop

cannot be inserted.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Proxxon FET Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info